Pair of 15" Baer Brakes Sport Front Brake Rotors for 2015, 2016 and 2017 GT Mustangs equipped with the Performance Pack.
Are you looking for a way to upgrade your 2015-2017 GT Mustang with Performance Package? If you drive your new pony harder, consider swapping your boring factory rotors with these 15" Baer Brakes 99001-020 Front Brake Rotors! Order yours today from CJ Pony Parts!
Baer Brakes Front Rotors Features and Benefits:
- Direct-fit upgrade won't require modifications or special tools
- Cross drilling and slotted design
- Bright zinc-coated finish is resistant to rust
- Provides race-ready braking technology to your factory performance package
- Vented design with 15" diameter
- Compatible with factory brake calipers
- Sold as a pair for the driver and passenger sides
This pair of upgraded front brake rotors from Baer Brakes are designed to be a direct-fit upgrade to your GT's original factory rotors. These rotors will provide better braking and enhanced driving performance to your pony's performance package features, and the stylish and beautiful zinc-coated finish means that the rotors are ultra-protected from rust and water damage and will be gleaming like new for years to come. The cross-drilled and slotted design of each rotor will provide your Mustang with an upgraded look while also giving your brakes race-ready road technology. Simple to install, this pair of front rotors will have you loving your everyday commute like it's a Sunday morning cruise! Pick up your pair of front brake rotors from CJ's today!
Vehicle Fitment Note: This pair of Baer Brakes front rotors will only fit 2015-2017 GT Mustangs with the factory Performance Package. They will NOT fit GT350, GT350R, base-model GT, Performance Pack EcoBoost, base-model EcoBoost or standard V6 model Mustangs.
We all know the thrill that comes with upgrading your Mustang’s power and performance so it’s the loudest and fastest on the block. While this excitement makes for the ultimate driving experience, it’s important that you stay safe behind the wheel. Making your car go faster is only part of the upgrade process when you're upgrading your Mustang for performance. You also have to consider how to get your powerful Mustang stopped again. For that, CJ Pony Parts recommends the products from Baer Brakes. CJ Pony Parts offers Baer Brakes for any Mustang on the road, with most performing much better than the OEM products. Check out our selection for your model-year pony today!
Order this Pair of 15" Baer Brakes 99001-020 Sport Front Brake Rotors for your 2015, 2016 or 2017 GT Mustang equipped with the Performance Pack from CJ Pony Parts today!
Product ReviewsWrite a review
I am always suspicious when things look too good to be true. Is the installation of these rotors really that easy? In the past I have had to collapse or compress the brake pads before I could slide the caliper over the rotors. This is not needed? BJ
You Might Also Like
Regular Price: $229.99
Special Price: $218.49
CJ's Low Price:$199.00
These 15 inch Baer Sport Rotors are bent and will be direct replacements for the factory rotors on all Performance Pack equipped 2015 through 2017 Mustangs. They come cross rolled and slotted for a custom look and higher performance and also come with a zinc coating to prevent against rust.
Like I mentioned, these Baer Sport Rotors are going to be a direct replacement for your factory with no modifications required. They will work with stock or aftermarket pads, and there is going to be a bedding procedure required, which we will explain later.
As you can see, our factory rotors aren't in bad shape. We can see some rust starting on the edges, that's going to be a huge upgrade going with the Baer rotor over our stock ones.
The installation, the first thing you do is get the car off the ground, remove the wheel. I do suggest using some penetrating oil and spray it in here as sometimes the rotor does tend to stick to the hub.
We moved underneath our car, which is 100 percent not necessary for the installation. We're doing this only so you can see the bolts better. To remove the caliper and get it out of the way is 1 bracket bolt down here and 1 up top. The bolts off, now we can remove the caliper. Just kind of shimmy it off and put it out of the way back here on the frame rail. If you're lucky at this point, the rotor will just come off. In our case, you can see it's on there pretty good. We're going to start with the soft hammer to see if we can knock it loose.
The rotors are side specific, so make sure you grab the correct one. I'm sure some of you are wondering about the weight on these rotors and we had the Eradispeeds in the past, which are the 2 piece rotor. The Eradispeed does weigh less than your factory rotor. If this is a 1 piece rotor just like your original, the weight is just about the same as the factory.
Before we reinstall the caliper, I'm just going to put 1 lug nut in place here. That'll keep the rotor tight against the hub, makes it easier to get the caliper back on. It's easier to start at the top, sort of work that on and then reinstall the bolts. Then we can tighten these up. Reinstall the wheel, repeat the process on the other side and you're installation is finished.
Once you get both rotors installed, your wheels back on and torque inspect, you're ready to take it for a drive. To make sure the rotors last long and perform properly, you want to break them in. To do that, drive for about 5 to 6 days normal driving. Normal stop-and-go, nothing real heavy. After that, do a couple of heavy stops. 60 to 0, 45 to 0, 30 to 0. Do a bunch of those and then drive around a little bit to cool it off and they'll be ready to go.
The installation is very simple. All you need is to get the car up in the air and use a 15 inch wrench and a ratchet and it'll take you about an hour to do both sides and you'll be back on the road in no time.