Bilstein B6 HD Strut and Shock Kit for 2005, 2006, 2007, 2008, 2009 and 2010 V6 and GT Mustangs and 2007, 2008, 2009, 2010, 2011, 2012, 2013 and 2014 GT500 Mustangs.It is always best to upgrade all suspension components at the same time. This full Bilstein damper kit will provide superior handling as well as a predictable and well balanced car. Includes two 36mm B6 Heavy Duty front struts and two 46mm B6 Heavy Duty rear shocks. After installing Bilstein struts and shocks, your Mustang will gain additional traction and enhanced stability. The new found performance will be accompanied by an exceptionally comfortable street ride. Bilstein tuned the struts and shocks to handle the occasional track outing as well as street duties. Upgrading springs will boost handling performance even further but the B6 HD struts and shocks will work with stock springs as well.
Bilstein 36mm B6 HD Series struts and 46mm B6 HD Series shocks improve handling and stability without sacrificing ride comfort. Super damping abilities make Bilsteins ideal for the driver who demands superior performance while maintaining an exceptional street ride. Mono-tube construction ensures greater damping force and better handling with its large effective area of the working piston. Bilstein B6 struts and shocks are for those that expect more damping power from their shock absorbers but don't want to opt for an all-out sports model. Bilstein road and track tests their shocks for fine tuning.
Bilstein entered the motorsports industry over 50 years ago and is still a leader in suspension components. Not only does Bilstein make aftermarket performance shocks, but they also produce OEM shock absorbers. Many makes and models utilize factory Bilstein shocks including certain Ford Mustangs. Bilstein provides performance parts for many types of racing including Fomrula One, rally racing, 24 hours at LeMans, and NASCAR.
*Front wheel alignment will need to be set to OE specifications after installation of Bilstein struts.
Product ReviewsWrite a review
I have a '13 GT with Ford Racing K-springs and want to upgrade my struts (& shocks) with Bilstein struts. I already have a pair of GT500 strut mounts so which model of Bilstein should I order, the 05-10 or 11-14? What other struts can you recommend?
You Might Also Like
CJ's Low Price:$886.99
Regular Price: $1,129.99
Special Price: $1,016.99
CJ's Low Price:$2,399.99
Here you can see it closer with the top of the strut that we're using, which again is a 2005 through 2010 GT or GT 500 style. The reason we're going for that is so we can use the GT 500 heavy duty strut mounts. The factory struts '11 through '14, this is actually the same thickness at the top so these upgraded strut mounts will not work.
For this installation you'll need jack and jack stands or a lift, pole jack, and a jack, 3/8 ratchet, 10 mm socket, 13 mm socket, 15 mm socket, 17 mm socket, 21 mm socket, 22 mm socket, 5 mm Allen key, 15 mm wrench, 17 mm wrench, 18 mm wrench, coil spring compressor, and safety glasses.
You'll want to start by getting your Mustang up off the ground and then we remove the front wheels. We'll start by disconnecting the strut from the sway bar end link here, put a wrench on the back and remove this nut. You're going to remove the brake line next. There's a small bolt behind the strut, remove that and remove the bracket.
Now you're going to remove the Christmas Tree clip for the ABS line. Now we're going to unbolt the strut from the spindle. You want to support the lower control arm before removing the lower bolt. The last step to remove the struts is four strut nuts located on top of the strut tower. You want to make sure you hold onto the assembly when you take the last one off and remove the strut assembly.
The only thing we're going to need from our original strut assembly is going to be our Eibach coil springs, so we'll grab our spring compressors, remove the spring, and install them onto our new struts. Once it's compressed, you can remove the upper strut nut, which holds on our strut mount. Here you can see again why we went with the GT 500 strut versus the factory 2011 and up style. See this shoulder goes all the way up to the threaded section here and if we try to install our GT 500 mounts they won't go down far enough. Here's a comparison again with a GT 500 mount here and the stock mounting. It's a much beefier piece and definitely better for high performance applications.
We'll install our Eibach spring onto our new strut, make sure it's seated properly, and install our new strut mount. Make sure that's lined up as well and then we'll tighten it down. We've got to make sure our spring is lined up in the base of our strut, as well as the top of our strut mount. We can release tension on our spring compressor and we're ready to reinstall in our car.
You want to make sure this arrow is facing outward toward the mount where the strut mounts to the spindle. We'll get the spindle back up to place into our strut and now we'll going to work on reconnecting our ABS line and brake line. Push that through first. I should mention the hole back here on our Bilstein is actually not threaded like the factory one is, but the hardware provided by Ford will thread into it and hold it in place. We're going to reconnect our sway bar and repeat the process on the other side and remove on to the rears.
To start the rear shock installation you have to get to the top shock nut, which is going to be located behind these panels here. We want to pull that aside and that's it right there. You'll want to remove both sides while you're in the trunk and now you can move under the car.
Once you have the car up in the air the rear shocks remove by removing this bolt right here. Unfortunately if you pull it out it's going to hit your sway bar, so you're going to start by removing the end links so the sway bar can swing down. You'll want to support the axle. Now we can pull the sway bar down. Install a lower washer and lower bushing, reinstall the factory nut and bolt, and now we can put our sway bar back into place.
We can release our pole jack and now we can go in the trunk and install the nuts on top of our shocks. We do this install on the ground. You can use your floor jack on the pumpkin and simply jack the rear up into place to put these on. If you're doing it on a lift like we are just put the car back on the ground and they'll go up into place. You want to install the top bushing, washer, and then the nut and tighten it down. If it spins you can use a 5 mm to hold the strut assembly and then tighten with a ratchet wrench and your installation is finished.
Unfortunately, the snowy roads here in Pennsylvania keep us from doing our normal test drive, but given the fact that Ford looked to Bilstein for high performance shocks and struts to go with the '03 through '04 Cobra, as well as the Cobra R, we know they're going to do a great job on our 2011. Installation should take you around three hours, so you'll be back on the road in no time.