Redline Tuning Bolt-In QuickLIFT PLUS Hood Strut Kit for all 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 and 2014 Mustangs with a Stock Hood.Redline Tuning has released a completely new design for their hood strut kits. The result is a patented bolt-in design that utilizes a fender bolt and an existing hole in the hood frame for a truly a bolt-in installation with the stock hood. Order yours today from CJ Pony Parts and you’ll be pleased with having a hood that operates smoothly, reliably and consistently on your 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 or 2014 Mustang.
QuickLIFT PLUS Features:
- Two Black E-Coated Custom Valved, Gas Springs
- Progressive, Slow Release System
- Black Powder-Coated Hardware
- Full Color Installation Manual
This Redline Tuning Bolt-In QuickLIFT PLUS Hood Strut Kit is manufactured to different specifications for each individual vehicle application. Exclusive end-of-force dampening slows the rate of extension over the final few inches of operation which creates a fluid, smooth lifting and closing process and also eliminates any stress that might have otherwise been imparted on the hood. These hood struts will lift and firmly hold the hood in its raised position.
After the installation of these Redline Tuning hood struts, you will never have to worry about the wind, or a limb of your own, bumping the prop rod and getting your fingers crushed and caught under the collapsing hood. This kit keeps the prop rod from obstructing the view of your clean engine bay as well as ensures it stays open until you want it closed. The two black, e-coated gas springs that lift and hold your hood without the need for the poorly placed prop rod are a welcome addition under the hood of anyone’s 2005-2014 Mustang.
*For use on stock hoods ONLY!
Product ReviewsWrite a review
will they fit a 2007 gt500-----------the upper holes in my stock hood look more sqare than the 5.0 in the vidio
Will these lifts fit a 2008 Shelby GT500? Thanks.
What about my 2015 GT?
Will these redline work on shelby 500 2014
will these hood struts work on a 2005 saleen s281sc
Can these be used on the Cobra R hood for a 2014 GT?
Is there a warranty on this kit?
The installation instructions say the 05-09 hood inserts are different from the 10 and up and are NOT interchangeable. Does this kit come with both? I didn't see an option to choose the correct year.
You Might Also Like
CJ's Low Price:$119.99
CJ's Low Price:$89.99
California Pony Cars Hood Strut Kit NXT Generation GT500 2007-2014/V6 and GT 2011-2014/Boss 302 2012-2013From:CJ's Low Price:$117.99
The lower bracket's going to mount to this fender bolt right here. The uppers go in this existing hole in your hood. This is the upper mount. Basically, you're going to want to loosen it up to the point that this washer is still hanging on, but has enough space so we can slide it through the hole. We want to put it through on an angle, and then pull against the hood while you tighten it up. We're going to get it just hand-tight for now, and what you'll want to do before you actually tighten it up with your wrench, you'll want to slide it toward the outside of the hood as far as possible, and then tighten it down. This will keep the strut from interfering with your shock tower when your hood is closed.
Now we're going to remove our fender bolt, install our bracket. The brackets are not side specific. If your car still has the factory air tube that goes from the cold air kit to the firewall, there's going to be a bracket that's going to mount right here. You'll have to take the bracket off the top studs and move it to the bottom to clear that stud.
Our last step is to install the strut itself. We're going to place the end of the strut over the ball on the end of the bracket. We're going to make sure the body of the strut is facing upward keeping any condensation out. Just place it over and press it into place, and then you'll want to repeat the process on the other side. Now for our last step, we're going to remove our factory prop rod, and our installation's complete.
We're going to try out our new hood struts, pull it up about halfway and then just let it go. It will slow down at the top. That's what Ford should have done when they built these cars. Installation is pretty straight forward, should take you no more than about 20 minutes. You'll be back on the road in no time.