Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967

Dynacorn: 3745CWT
CJ's Low Price:
$149.99
1481068800 62451
Also check out this center floor pan brace for your Bronco project.
CJ's Low Price:
$139.99
Qty
Earn 149 RPM Points What's this?
Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967
Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967 Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967 Play Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967 Video 1
Dynacorn

Product Description

Dynacorn Rear Floor Pan Brace in Weld-Thru Primer for all 1966-1967 Broncos.

Restoring a classic Bronco is a huge endeavor. Finding the correct parts necessary to complete the installation may be the most difficult aspect of the project. If you have been searching for a Rear Floor Pan Brace for your 1966-1967 Ford Bronco then your search is over! We offer a 3745CWT Dynacorn Rear Floor Pan Brace that is perfect for any Bronco restoration.

Product Details:
- Fits 1966-1967 Ford Bronco
- Premium Quality Dynacorn Part
- Factory Style Replacement
- Structural Support Item
- Weld-Thru Primer Finish

Advantages of Weld-Thru Primer:
- Reduces Prep Time When Welding New Parts to New Parts that are Both Covered in the Weld-Thru Primer
- Reduced Spatter
- Lower Distortion of the Panels
- Superior Conductive Properties that Help Minimize High Heat Zone Problems
- Eliminates Corrosion that would Form Between Overlapped Panels or Multi-Layered Spot Welds
- Helps When Welding a New Panel to Old Metal
- Lower Resistance at the Weld Surface Allows Better Penetration into the Denser, New Steel that Helps Forgive an Old Alloy's Problems with Porosity and Impurities
- Helps Prevent Resin Build up Between Welds that can Trap Moisture in the Old Porous Steel that Leads to Failure at the Weld Borders

This piece mounts under the front of the rear floor bed and the back of the upper seat platform. This will tie together the front floor and the rear floor bed and provide extra structural support. Since this is a Dynacorn part, it is made from high quality stamped steel.

Order a 3745CWT Dynacorn Rear Floor Pan Brace in Weld-Thru Primer for your 1966-1967 Bronco from CJ Pony Parts today!

Similar Bronco Parts

similar Bronco parts More Bronco Parts  

Installation Instructions

Mustang Installation

Bronco Applications

This product will fit the following Ford Bronco years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 125.56ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 127.6ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

Dynacorn Floor Pan Brace In Weld-Thru Primer Rear Bronco 1966-1967 Video Transcript
By Bill Tumas: We’re here with a rear floor pan brace fitting your 1966 through 1967 Bronco from Dynacorn. This is a reproduction of the original rear floor pan brace found in your 1966 through 1967 Bronco. It comes in a weld through primer making it ready to install. It includes the bracket and is pre-drilled for installation. This is going to tie the front and rear floor pans together and support them. This rear floor pan brace and other restoration sheet metal from Dynacorn for your classic Bronco are available right here at CJPonyParts.com.