Eastwood Plasma Cutter Versa-Cut 60

Eastwood: 14099
MSRP: $839.99
CJ's Low Price:
1477008000 12924
Earn 679 RPM Points What's this?
Eastwood Plasma Cutter Versa-Cut 60
Eastwood Plasma Cutter Versa-Cut 60 Play Eastwood Plasma Cutter Versa-Cut 60 Video 1

Product Description

Eastwood Versa-Cut 60 Plasma Cutter

Designed to cut steel, aluminum and stainless steel from 0.010" to 0.875" with ease, this 220 volt/50-60Hz plasma cutter is sure to get the job done. The amp output is adjustable from 20-60 amps. An adjustable air pressure regulator assures long life, accurate cuts and ease of use.

-Heavy duty Mosfet inverter
-Internal moisture separator
-20 ft torch
-10 ft ground cable
-Self-starting arc for use on floor panels and exhaust where rust and contaminants may be an issue.

Product Reviews

Write a review
Eastwood Plasma Cutter Versa-Cut 60 is rated 4.574074074074074 out of 5 by 54.
Rated 5 out of 5 by from Awesome cut I am building a bbq grill for my church and thought this would be a good time to appeal to my wife's good senses ,this thing is awesome. I put it to the test right out of the box cutting 3/8 plate,cut through it like butter. I have been a hobby shop guy for 30 years and must say this plasma cutter and my mig welder best tools I own.great machine I would buy it over Lotos again. Well built easy setup. Two things I would change stand off tool needs to be more robust, and stock consumables better and not have to Waite on back order. One more thing the cutter cord length is awesome a lot longer than China machines
Date published: 2016-05-27
Rated 5 out of 5 by from Cuts like a laser I bought this to replace a inexpensive Ebay plasma cutter with no warranty. It broke (leaving me with a 300 dollar paperweight) so I knew I wanted a decent warranty as well as more power so I got the Versa Cut 60, (comes with a 3 year warranty). I've had it for about three weeks and I'm really enjoying using it, made some difficult cuts at steep angles on 1" pipe but it worked great! On straight cuts with the guide it's as easy as using a magic marker that just happens to vaporize steel! It seems like it has double the power of the one I used before! I'm really liking this! As much fun as a new gun! I really feel like I can depend on this tool to make the difficult easy...
Date published: 2015-04-28
Rated 4 out of 5 by from Cuts well, easy to use I bought this because I'm restoring/rebuilding a '65 F350 with a very rusty flareside bed and I knew there was a lot of metal removal ahead of me. The unit cuts well and works well but the air pressure adjuster doesn't work and I've been unsuccessful at getting any help from Eastwood. One of the reasons I bought this over a Lincoln was the price and the fact that others had commented in reviews about how responsive Eastwood was for tech support, but this has not been my experience. As long as you can regulate your air pressure ahead of the unit its fine. Like others, mine continues to blow air after releasing the trigger, which I assume is to cool parts, not sure, minor annoyance.
Date published: 2015-01-05
Rated 5 out of 5 by from Eastwood 60 Plasma Versa Cut My 1st plasma cutter. Important to learn how to set amp/air, the right settings eliminate blow back, completes cut on 1st pass, and makes smother cut. Thicker material require slower cutting. Cuts very good on rusty metal. I've cut 1/2 inch by following a guide with the right settings and cut looked very smooth. Easy to destroy consumables with blow back. After several replacements I now use a metal drag attachment which seems to help. Eastwood guarantee for me has been exceptional. I'm just a hobby and occasional user, but at 1/2 the price of American 40 amp plasma, it far exceeded my expectations.
Date published: 2015-03-02
Rated 5 out of 5 by from excellent unit Cuts wonderfully and has plenty of power. We have a miller at work and tbis thing was less expensive and runs circles around it. Consumables are better priced as well. One questionable item is that i think the plasma will activate without air pressure. This caused me to have to clean my electrode and nozzle twice before i realized what i was missing. Compressor was hooked up but was only supplying about 5 psi because it was off. The only reason in mentioned is the miller has an air detection light to tell you if there isnt sufficient air supplied....
Date published: 2015-07-29
Rated 5 out of 5 by from So Far Its Amazing I have an existing thermo dynamics plasma and a acetylene torch. The thermo dynamics is a nice machine but only cuts a 1/4 inch and the acetylene is awesome but can be a pain to use in certain areas. So I wanted a larger plasma and since any name brand is 2 to 3 times the cost and still not capable of the Versa 60 I thought what the heck ill try it. I cut some 1/4 stock like nothing, then for fun grabbed an old brake rotor, rusted bad, just clamped it on turned up the juice and bam sliced it right up. Spent the next couple hours cutting material for an awesome welding cart. Clamped a straight edge on some 16 gauge and this just glided right along cutting beautiful straight lines. The long cables are great as well. Great plasma cutter!
Date published: 2015-02-26
Rated 5 out of 5 by from Does exactly what its advertised to do First off I want to mention that the unit came very well packed with foam and cardboard tubes so of course there was no external damage during shipment. I did test passes on 1/8, 1/4, 1/2, and a piece of 1"( I had no 7/8). It had no problem cutting through all but the 1" leaving about an 1/8 so therefore I'm certain it would sever 7/8 with no problem. My primary use will be to cut shapes from 1/4 and the occasional 1/2. The higher than competitors advertised duty cycle was a big selling point to me.
Date published: 2015-05-06
Rated 5 out of 5 by from Warrantee I purchased a 60 amp Versa-Cut Plasma Cutter a year ago. All of a sudden it would cut out while cutting and not ignite. I called Tech Support at Eastwood and talked to Ed. After hearing my explanation, He said he would do the paper work and have my cutter picked up by Fed-Ex and ship a new unit. Yep, it was that simple. I boxed it up and it was picked up by Fed-Ex the next day. Eight days later a new unit was delivered to my door. Absolutely the best Customer Service I have ever experienced.
Date published: 2015-04-09
  • 2016-10-21T07:54CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_54
  • loc_en_US, sid_EWPC, PRD, sort_relevancy
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 166.87ms

Product Questions

Can the plasma cutter ship overnight

Asked by: cupcake5
Overnight shipping is available at a additional cost.
Answered by: CJPP Dave
Date published: 2015-12-15

What is the air compressor pressure requirements for operation

Asked by: Fordpickup51m
You will need 5-7 CFM @ 60 psi for proper operation.
Answered by: CJPP Dave
Date published: 2015-11-02
  • 2016-10-21T08:15CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_EWPC, PRD, sort_recentAnswersFirst
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 166.11ms

You Might Also Like