EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks

CJ's Part Number: FP58
CJ's Low Price:
$210.00
1481241600 63220
Be sure to pick up a new 1965-1968 or 1969-1970 EFI Fuel Tank to pair with your new EFI Fuel Pump!
CJ's Low Price:
$235.00
Qty
CJ's Low Price:
$225.00
Qty
Earn 210 RPM Points What's this?
EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks
EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks Play EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks Video 1

Product Description

In-Tank 190 LPH EFI Fuel Pump Assembly for use with EFI Fuel Tanks.

When increasing the horsepower of your car, you are increasing the amount of fuel being used, and the rate at which it is being used. The stock fuel pump for your car typically cannot keep up with these increases. Fortunately, CJ Pony Parts has your need for speed covered with this high performance In-Tank 190 LPH EFI Fuel Pump Assembly!

This fuel pump module is designed to work with CJ Pony Part's EFI fuel tanks (FT18 and FT19) which have a special reservoir tray already installed in the fuel tank. This reservoir tray is a must in a fuel injected application to prevent the car from fuel starving under hard acceleration and cornering.

EFI Fuel Pump Features and Benefits:
- Genuine high-performance Walbro fuel pump
- Up to 190 liters per hour of fuel flow
- Supports engines up to 450 horsepower
- Operating pressure of 0-100 psi
- In-tank wiring harness included
- Heavy-duty, 10-gauge mounting plate to prevent warping
- 1/4" NPT supply and return line
- Barbed vent fitting
- Oven brazed fittings
- Made in the United States of America

This in-tank fuel pump module uses a Walbro high performance fuel pump that supports up to 450 horsepower and feeds the motor fuel at 190 liters per hour. The supply line, return line, internal wiring harness, insulator sleeve and filter sock are included with the EFI fuel pump module. The heavy, 10-gauge mounting plate in this kit will eliminate any potential warping and is yellow-zinc plated to prevent rusting. It contains the correct fittings for the supply line, return line, vent, and electrical connector.

Please Note: This fuel pump module is to be used in EFI fuel tanks FT18 and FT19.

*Gasket and screws with O-rings not sold with pump, they are included in the EFI fuel tanks.

If your vehicle isn't performing well and is using more fuel, it might be something with your fuel system, which is vital to getting fuel to the engine and keeping your car running well. Oftentimes, there are two culprits within the fuel system that can stop fuel from getting to your engine – the Fuel Pump and Filters may need replaced. CJ Pony Parts has these parts and can help you get your restoration back on the road in no time.

Order this In-Tank 190 LPH EFI Fuel Pump Assembly for use with EFI Fuel Tanks from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Fuel Injected  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 190.34ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 193.64ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

EFI Fuel Pump Assembly 190 LPH In-Tank For EFI Fuel Tanks Video Transcript
By Bill Tumas: We’re here with a 199 liter per hour in-tank fuel pump assembly fitting your 1965 through 1970 Mustang with our EFI conversion tank. This in-tank fuel pump assembly is designed to be used with our EFI conversion tanks on your 1965 through 1970 Mustang. Starts off with a heavy duty 10-gauge steel plate with the correct fittings and goes down to a Walbro 190 liter per hour pump and the correct sock making a drop in assembly. This is made right here in the USA. and will support up to 450 horsepower. These fuel pump assemblies are available individually or as part of our EFI conversion fuel tank kits.