AMK Products Master Engine Fastener Kit Shelby GT500 1967

AMK Products: 67M-428PI
MSRP: $147.25
CJ's Low Price:
$140.99
Ships in 5-7 Days This item typically ships within 5-7 days1408492800
Earn 140 RPM Points What's this?
EFK331

Product Description

AMK Products Master Engine Fastener Kit for all 1967 Shelby GT500s.

This Master Engine Fastener Kit from AMK Products includes 180 total pieces of factory correct, OE style fasteners that are required to properly reassemble the engine components which attach to the long-block on your 1967 Shelby GT500's 428 Police Interceptor engine. This kit is specifically assembled for all 1967 Shelby GT500s.

AMK Products' Master Engine Fastener Kit includes individually packaged sets of hardware for various applications on your 1967 Shelby GT500's 428 Police Interceptor engine. Each package is thoroughly labeled so you know exactly where it goes on your FE big block engine. The individual sets of hardware also include the total number of pieces that are required for the specific application. Most of the included fasteners are either meticulous reproductions of the originals or new old stock!

Master Engine Fastener Kit Includes:
- Air Cleaner: 3" Double End Studs, Wing Nuts (4)
- Carburetor Return Bracket: Hex Screw/External Tooth Washer Assembly (2)
- Carburetors: Studs, Special Nuts (16)
- Crank Pulley: Hex Place Bolts (3)
- Crankshaft Damper: Hex Bolt, Flat Washer (2)
- Distributor: Hex Screw/Split Washer Assembly (1)
- Distributor Points and Condenser Dual Point: Slot Pan Head Machine Screws (5)
- Engine Block Drain Plugs: External Hex Pipe Plugs (2)
- Engine Fan to Clutch: Hex Screw/Split Washer Assembly (4)
- Engine Fan Clutch to Water Pump: 7/16" Hex Screw/Split Washer Assembly, "SEMS" (4)
- Exhaust Manifolds: Special Ramp-Lok Hex Screw/Conical Spring Washer Assembly (32)
- Fuel Pump: Hex Screw/Split Washer Assembly (2)
- Ignition Coil Strap and Bracket: Hex Screw/Split Washer Assembly, Hex Washer Head Screw, Hex Nut (3)
- Intake Manifold: Hex Bolts, Flat Washers (20)
- Intake Manifold Rear Plugs: External Hex 3/8" National Pipe Thread Plugs (3)
- Oil Filter Adapter: Hex Screw/Split Washer Assembly (4)
- Oil Pan: Special Hex Screw/Split Washer Assembly (20)
- Roadraft Tube or Vent Adapter at Rear of Intake: Hex Washer Head Screws (2)
- Starter: Hex Screw/Split Washer Assembly (3)
- Throttle Bracket to Intake: Hex Screw/External Tooth Washer Assembly (2)
- Timing Cover: Hex Washer Head Screws, Hex Machine Screws (10)
- Aluminum Valve Covers: Hex Bolts "RBW", Flat/Split Washers (30)
- Water Neck: Hex Screw/Split Washer Assembly (2)
- Water Pump: Hex Screw/Split Washer Assembly, Hex Bolt at Lower Right Side (4)

Buying individual sets of engine hardware for your 1967 Shelby GT500's 428 Police Interceptor engine can be expensive and time consuming if you're not sure which hardware you need. This Master Engine Fastener Kit makes it easy by including authentic style hardware that specifically fits your 1967 Shelby GT500. With a Master Engine Fastener Kit from AMK Products, you will not only save time and money, but you will have the confidence knowing your 1967 Shelby GT500's 428 Police Interceptor engine is going to be reassembled with the finest factory correct hardware on the market!

AMK Products produces the most factory correct hardware for your classic Mustang. No matter what kind of Mustang you're building, there's no company better for nuts and bolts than AMK Products!

Similar Mustang Parts

similar mustang parts More Mustang Engine Fastener Kits  

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a Review