AMK Products Master Engine Fastener Kit Shelby Cobra GT500 1968

AMK Products: 68M-428PI
CJ's Low Price:
$149.99
1419033600 12498
Earn 149 RPM Points What's this?
EFK677

Product Description

AMK Products Master Engine Fastener Kit for all 1968 Shelby Cobra GT500s.

This Master Engine Fastener Kit from AMK Products includes 164 total pieces of factory correct, OE style fasteners that are required to properly reassemble the engine components which attach to the long-block on your 1968 Shelby Cobra GT500's 428 Police Interceptor engine. This kit is specifically assembled for all 1968 Shelby Cobra GT500s.

AMK Products' Master Engine Fastener Kit includes individually packaged sets of hardware for various applications on your 1968 Shelby Cobra GT500's 428 Police Interceptor engine. Each package is thoroughly labeled so you know exactly where it goes on your FE big block engine. The individual sets of hardware also include the total number of pieces that are required for the specific application. Most of the included fasteners are either meticulous reproductions of the originals or new old stock!

Master Engine Fastener Kit Includes:
- Air Cleaner with Holley Carburetor: 2.6" Double End Stud, Wing Nut (2)
- Carburetor without Spacer: Studs, 7/16" Nuts (8)
- Crank Pulley: Hex Place Bolts (3)
- Crankshaft Damper: Hex Bolt, Flat Washer (2)
- Distributor: Hex Screw/Split Washer Assembly (1)
- Distributor Points and Condenser Single: Slot Pan Head Machine Screws (3)
- Distributor Vacuum Unit: Slot Pan Head Screws (2)
- Engine Block Drain Plugs: External Hex Pipe Plugs (2)
- Engine Fan to Clutch: Hex Screw/Split Washer Assembly (4)
- Engine Fan Clutch to Water Pump: 7/16" Hex Screw/Split Washer Assembly, "SEMS" (4)
- Exhaust Manifolds: Special Ramp-Lok Hex Screw/Conical Spring Washer Assembly (32)
- Fuel Pump: Hex Screw/Split Washer Assembly (2)
- Ignition Coil Strap and Bracket: Hex Screw/Split Washer Assembly, Hex Washer Head Screw, Hex Nut (3)
- Intake Manifold: Hex Place Bolts, Flat Washers (20)
- Intake Manifold Rear Plugs: External Hex 3/8" National Pipe Thread Plugs (3)
- Oil Filter Adapter: Hex Screw/Split Washer Assembly (4)
- Oil Pan: Special Hex Screw/Split Washer Assembly (20)
- Starter: Hex Screw/Split Washer Assembly (3)
- Timing Cover: Hex Washer Head Screws, Hex Bolt, Hex Machine Screws (10)
- Aluminum Valve Covers: Hex Bolts "RBW", Flat/Split Washers (30)
- Water Neck: Hex Screw/Split Washer Assembly (2)
- Water Pump: Hex Screw/Split Washer Assembly, Hex Bolt at Lower Right Side (4)

Buying individual sets of engine hardware for your 1968 Shelby Cobra GT500's 428 Police Interceptor engine can be expensive and time consuming if you're not sure which hardware you need. This Master Engine Fastener Kit makes it easy by including authentic style hardware that specifically fits your 1968 Shelby Cobra GT500. With a Master Engine Fastener Kit from AMK Products, you will not only save time and money, but you will have the confidence knowing your 1968 Shelby Cobra GT500's 428 Police Interceptor engine is going to be reassembled with the finest factory correct hardware on the market!

AMK Products produces the most factory correct hardware for your classic Mustang. No matter what kind of Mustang you're building, there's no company better for nuts and bolts than AMK Products!

*Not for use on 1968 Shelby Cobra GT500KRs which are equipped with the 428 Cobra Jet engine.

Similar Mustang Parts

similar mustang parts More Mustang Engine Fastener Kits  

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a Review