Ford Upgraded Lower Engine Mount for all 2013, 2014 and 2015 Focus STs.
Do you want to gain a smoother, quieter ride and significantly reduce wheel hop in your 2013, 2014 or 2015 Focus ST? The increased strength and durability this new Ford Upgraded Lower Engine Mount will provide is just the part you need!
This is a sturdy, more rigid motor mount than what was originally found in the 2013-2015 Focus STs. A stronger, firmer mount means there will be less movement and vibration from the engine; something everyone can agree is a welcome improvement. This lower motor mount is the stock lower mount found in Focus electric cars and is much thicker and stronger as a result of the need to hold and support the heavier engine and related components found in the electric cars.
This was a suggested replacement part from a Ford Bulletin, so you know it is the best available option as an upgrade. So if your lower motor mount isn't as sturdy as you would like, or it was damaged somehow, this is the part you need to fill the void and solidify your engine's mount and position.
Please Note: This lower engine mount is the factory original part for all 2011-present Ford Focus electric cars.
The Ford Motor Company has made many of their parts internally, which means if you're looking to replace a part, there's no better source than the OEM parts from Ford we have available here at CJ Pony Parts.
Order a Ford Upgraded Lower Engine Mount for your 2013, 2014 or 2015 Focus ST from CJ Pony Parts today!
Similar Focus PartsMore Engine
Product ReviewsWrite a review
Is it true what Roameroll007 claims? Is this the same RMM that comes installed as stock on the 2015 Focus ST?
Ford Lower Engine Mount Upgrade Focus ST 2013-2015,will it work on a 2015 ford escape 2.0 Thank You
Will this fit on the new 2015 Focus ST?
You Might Also Like
CJ's Low Price:$389.99
CJ's Low Price:$780.99
CJ's Low Price:$199.99
The main culprit of the wheel hop in the Focus is the rear engine mount. The mount is made of a soft rubber, allows the engine to flex a little bit too much, calls in the hop issue. The easiest way to fix this is to replace the mount with something a little bit firmer. Today, we're going to move our factory mount, and replace it with this electric mount from Ford.
This is the factory motor mount found in the electric Ford Focus. If you're familiar with electric cars, you know they have a ton of torque. Ford realizes this and uses a much heavier duty engine mount for their Focus. Thankfully, it's a direct swap for the Focus ST, making for a low-cost upgrade.
For this installation, you need a jack and jack stands or a lift, 3/8 ratchet, T30 torx bit, 15mm deep socket, 13mm socket, 6-inch extension, 15-mm wrench, 13-mm wrench, 3/8 torque wrench, and safety glasses.
Once you have your car up in the air, you want to locate the rear engine mount, which is right here. To get to it the first step, we're just going to remove this cover so you have easier access to the hardware.
We're going to start with the four nuts that hold the bracket here that goes between the bottom of the mount and our factory downpipe. Now we'll remove the bracket located here. There's one nut here you've got to remove, and the other one's up, kind of around the corner.
Next, we have to remove the bolt that holds the actual engine mount to this bracket. Remove the bolt that holds the mount to the subframe. Now we can slide it back, which makes it easier to access the last bolt we've got to get off here, and this one as well here, to remove this bracket so we can get the mount out of the car.
The last bolt for the bracket is one hidden down here in the bottom. Remove the bracket, and then we can remove our factory mount. Here you can see our stock ST mount versus the electric mount on the side here. This, I can actually move with my thumb. There's so much flexibility in this mount. This one, very, very solid, which should definitely help with our wheel hop problem.
Put our new mount up into place. Slide it back as we did before, and then we'll reinstall the bracket. When you get everything in place, just hand tighten it for now, and then we'll go back and tighten everything up.
Now we'll torque to 70-foot pounds. Reinstall the first part of the bracket. Now we'll reinstall the bracket up to our downpipe. Go ahead and keep everything loose at this point until you get it all into place. Now we can start tightening everything down.
Our last step is to reinstall the cover, and our installation is finished. Now we'll get or ST back on the ground. We'll take her for a test drive. We'll see how well it works.
Fortunately, this isn't the best day to do a test. Notice the thermometer on the car says five degrees. That's probably optimistic. It's a lot closer to zero or even below zero here right now. Let's go give it a shot and see if we notice any difference. Of course, you really can't hit it in first. It should just spin.
That's spinning through second as well. Looked pretty good in third, though. Good thing is, it was spinning. It wasn't hopping. Before, the car would hop really badly because it was fighting for traction. Now, it's just spinning, which is good because it's not hopping. It's not going to hurt the suspension. Not so good because it's cold out, and there's a lot of salt on the road, so we're going to end our test drive and head back to the shop.
It's hard to believe a small part like a mount made that much of a difference, but then again, given how flexible the stock mount was, I'm really not that surprised. The electric Focus engine mount got rid of all of our one, two shift hops and most of our launch hop as well. Installation should only take you around an hour. You'll be back on the road in no time.