Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017

Ford Performance: M-5A460-M
MSRP: $82.50
CJ's Low Price:
1477440000 61554
Continue to upgrade your 2015-2017 Mustang's handling by adding these Ford Racing parts to your order!
Earn 72 RPM Points What's this?
Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017
Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017 Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017 Play Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017 Video 1
Ford Performance

Product Description

Ford Performance Knuckle to Toe Link Bearing Assembly for all 2015, 2016 and 2017 Mustangs.

Improve the handling while taking out any compliance from the suspension on your 2015-2017 Mustang by ordering this Ford Performance Knuckle to Toe Link Bearing Assembly. As a part of Ford Performance's Assembled Handling Package, this assembly will have a significant impact on the overall performance on your S550.

Features & Benefits:
- Will Fit All 2015-2017 Mustang IRS
- Includes Two Bearings in Total
- Production-Styling Bearings
- Replacement for Rubber Toe Link Bushing
- Eliminates Suspension Compliance with Little Effect on Ride Quality
- Important Part of Ford Racing Assembled Handling Package
- Improves Handling, Specifically in Power Down Situations

This Knuckle to Toe Link Bearing Assembly from Ford Performance will directly replace the original rubber toe link bushing in the rear knuckle of your S550 Mustang with a high-performance, production style bearing. Coming with two bearings in total, this assembly will fit all 2015-2017 Mustang IRS and is a critical component of Ford Performance's popular, high-performance Assembled Handling Package. Once installed, this bearing assembly will improve your Pony's handling performance, especially during those power down situations. It will also remove any suspension compliance with very little, if any impact on the overall quality of your ride. This knuckle to toe link bearing assembly is a simple yet wonderful upgrade that will provide a great impact on your Mustang's handling performance.

*If you would like Ford Performance's full assembled handling package, it is available at CJ Pony Parts as part # MFR3AM8.

If you're looking for parts for your 2015-2017 Mustang, you should start by looking at the several Mustang parts that CJ Pony Parts offers from Ford Performance (formerly Ford Racing). By purchasing your Ford Performance parts from CJ Pony Parts, you know you're getting your Mustang parts from a reliable, reputable dealer, since CJ Pony Parts is a Top 10 Ford Performance Dealer and has been for the last 10 years. When you buy your Ford Performance Mustang parts from CJ Pony Parts, you know you have a winning combination.

So go ahead and order this Ford Performance M-5A460-M Knuckle to Toe Link Bearing Assembly for your 2015-2017 Mustang from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Bushings  

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017 is rated 4.0 out of 5 by 3.
Rated 3 out of 5 by from An Upgrade (maybe)... As upgrades go, this is one that most of us can do without. After viewing the installation video and making sure I had the proper Ball Joint Press, I decided to give it a try. Caution: Do not try this at home. No, just kidding but unless you are prepared to remove the hubs you will not get the new bearings back in the hub casting. I spent hours under the car trying to press the bearing in but never succeeded. It would not go in straight. I finally removed the hubs from the car and using my 20 ton shop press succeeded (very easily I might add) in both removing and pressing in the new bearings. These bearings are an improvement and are on par with the others in the hubs. But this is a very difficult installation.
Date published: 2015-07-27
Rated 5 out of 5 by from Ford Racing Knuckle to toe link bearings I installed a steeda stop the hop pack on my 2016 mustang GT with has the performance package on it and I still had wheel hop. The oem rubber bushing still let the car wheel hop, I installed the new Ford Racing toe link bushing and that did the trick, no more wheel hop. I used a C frame ball joint press and a 36 m.m socket to remove and install the new bearing. Ford tell you to use a 1 and a 1/4 socket which will only press on the inter rubber on the oem bearing and you will get no were. Yes I installed these under the car on jack stands. thanks CJ Pony for the great price and fast delivery . Glenn W. Jones
Date published: 2016-03-07
Rated 4 out of 5 by from Let's Talk Installation The Ford Performance instructions for installing this bearing kit are actually pretty good, but they don't do a good enough job of telling you which direction to insert the bearing and which side of the bearing to push in first. You'll notice in the photos there is a line around the circumference of the bearing shell closest to a beveled edge. There is also a beveled edge where the bearing goes facing toward the front of the car. I inserted the bearing into the beveled edge side of the race starting with the beveled edge of the bearing itself. So beveled edge to beveled edge. I hope that was the right approach, and it worked for me. It was just too hard to tell what Ford wanted you to do in the instructions. Whoever writes car parts instructions is clearly a seasoned mechanic, not a garage installer that would appreciate more detail. Anyway, using a rented ball joint press and after a lot of swearing at said ball joint press, I pressed out the old bushings and pressed in the new bearings. I had to take out the ball joint press assembly a couple times to make sure I ultimately seated the bearing "centered" in the race. You'll notice, which is kind of funky if you compare these bearings to the OEM bushing, that the bearing is wider than the OEM bushing. Therefore, there will be "bearing" sticking out on both sides of the mounting location. You need to make sure you have the same amount sticking out on both sides, which is why I had to take off the ball joint press to see if I was nice and centered, and then re-assemble it to press in a little more just to get it centered right. In the ideal world, the bearing would be designed to "bottom out" where it needs to be, but... life is unfair. The instructions state this will take 4 hours. It took me 2 and a large portion of that was figuring out how I would situate the stupid universal ball joint press. The instructions also suggest using a 1 1/4" socket to press out the bushing and press in the bearing. The 1 1/4" sock I have was not big enough, so I used my 1 3/8" socket. Use whatever does not exceed the OEM bushing circumference but rests on the metal, not the rubber. It will work also for this replacement bearing to press in. You will drop the stupid ball joint press and all the parts on the floor a zillion times, but eventually you'll get the hang of it and you'll accomplish the second bearing in what will feel like seconds. Just be sure to not put pressure on anything but the outside. The instructions also want you to use red Loctite on the bearing mating surface. I've never heard of using red Loctite on a bearing mating surface, but I figured at least it'd act as a sort of lubricant. I put the red Loctite in that recessed line on the bearing primarily and then let it seep a little around that area. The instructions weren't clear if I should coat the bearing mating surface or not, so I did it the way I did it. That seemed to work great. If anyone wants to take this bearing out one day... well, red Loctite. Getting the toe arm over the bearing in reassembly was a pain. I actually bent VERY LITTLE the toe arm bracket wider just to get it over the bearing, then used the bolt to tighten it all back down and torqued as specified. No issues expected (the arm is steel, not aluminum, so it won't "crack" with just a little "tolerance enhancing". As for performance... I haven't driven the car yet but I wanted to post these install thoughts.
Date published: 2016-10-03
  • 2016-10-25T07:51CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en_US, sid_M5A460M, PRD, sort_relevancy
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 6.14ms

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 211.37ms
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

Ford Performance Knuckle To Toe Link Bearing Assembly 2015-2017 Video Transcript
By Bill Tumas: We’re here with Ford Racing's knuckle to toe link bearing assembly, fitting all 2015 through 2016 Mustangs.

These bearings are going to replace the factory toe link bushing where the toe link connects to the knuckle. This is the part that causes suspension compliance and can make the rim a little bit loose on your Mustang. By installing these, you're going to tight up the rear suspension, allowing more traction especially when putting power to the ground. This is going to be a direct replacement for the factory bushings and factory style bearing.

These bearings are included in Ford Racing's handling, and package and are an excellent upgrade to all 2015 through 2016 Mustangs.