Ford Performance GT350R Leather and Alcantara Steering Wheel with Bezel Kit for all 2015, 2016 and 2017 Mustangs.
The wait is finally over! You now have the opportunity to own one of the most anticipated parts from the GT350R. This Leather and Alcantara Steering Wheel with Red Stitching and Bezel Kit M-3600-M350R will have any 2015-2017 Mustang looking and feeling like the newly released Shelby in no time!
The OEM Steering Wheel found on the new 2015-2017 Shelby GT350R features a race-inspired design and flat bottom. This steering wheel has been endlessly talked about since the debut of the GT350R. Also, the Leather and Alcantara Suede combination truly sets this wheel apart from your standard steering wheel. Featuring red contrast stitching around the entire perimeter of the steering wheel, the design works its way up to thicker grips at “10 and 2” and a red leather stripe at 12 O’clock. Ford Performance also includes a 3-Piece Bezel Kit, this kit has a black chrome appearance and will replace the silver bezels found on your OE steering wheel.
Features and Benefits:
- OEM Part Found on the 2015-2017 Shelby GT350R
- Leather Bottom and Red 12 O’clock Stripe with Alcantara Suede on Either Side
- Red Contrast Stitching Throughout the Entire Steering Wheel
- Flat Bottom Race-Inspired Design
- Slightly Thicker Diameter with More Defined “10 and 2” Grips
- Includes Black Chrome Bezels and Pre-Installed Wiring for Airbag and Electronics
- Reuses ALL Original Hardware from Existing Steering Wheel
- Requires Use of Your Factory Airbag and Steering Controls
- Direct Fit for ALL 2015-2017 V6, EcoBoost and GT Mustangs with a Manual Transmission
- Will Fit Right Hand Drive Models
*This WILL also fit 2015-2017 Automatic Transmission Mustangs equipped with paddle shifters. But it WILL require you to swap the trim panel, wiring harness and shifting mechanisms from your existing steering wheel to the new GT350R wheel. Without swapping over the original components the paddle shifters won’t work.
Please Note: Does not include Airbag, Hardware or Steering Wheel Controls.
If you're looking for parts for your 2015-2017 Mustang, you should start by looking at the huge selection of Mustang parts that CJ Pony Parts offers from Ford Performance (formerly Ford Racing). By buying your Ford Performance parts from CJ Pony Parts, you know you're getting your Mustang parts from a reliable, reputable dealer, since CJ Pony Parts is a Top 10 Ford Performance Dealer and has been for the last 10 years. When you buy your Ford Performance (formerly Ford Racing) Mustang parts from CJ Pony Parts, you know you have a winning combination.
Order the Ford Performance GT350R Leather and Alcantara Steering Wheel with Bezel Kit M-3600-M350R for your 2015, 2016 or 2017 Mustang from CJ Pony Parts today!
Similar Mustang PartsMore Steering Wheels
Product ReviewsWrite a review
At the end of the installation the airbag warning came on. Is there a way to fix that problem? Thanks
HOW MUCH DELIVERED TO MELBOURNE AUSTRALIA AN DOES IT NEED ANY MODIFICATIONS FOR 2016 AUSTRALIAN MUSTANG GT. thanks
Will the red match the red interior that came on my 16 mustang GT?
Will this steering wheel fit on a 2014 GT?
Will this fit RHD 2016 Mustang?
Will this fit on the 2017?
What's the difference in the gt350 and gt350 R steering wheels? I noticed there's a considerable price difference.
Hey cj I know this is a long shot but is there any way I could install this steering wheel onto my 2006 mustang? Please help
You Might Also Like
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$459.99
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$99.99
Regular Price: $49.99
Special Price: $39.99
The Ford Performance GT350R steering wheel makes an excellent upgrade for any 2015 through 2017 Mustang. It will work with a six-speed manual or the automatic and includes a steering wheel cell, which has an Alcantara suede finish with contrasting red stitching, a leather bottom and a red centering stripe as well.
Unique to the R package is you actually get these three trim pieces, which come in a smoked black chrome, which will look really good with your R wheel.
To install the steering wheel, you're going to get in the car, make sure your steering wheel is straight and then disconnect the battery. We're messing with the airbag. We're taking a lot of sensors and disconnecting things. Disconnect the battery first to make sure you don't have any issues. Then, we're going to remove the airbag.
The airbag's held in by spring clips, these small holes on the side here. I'm going to take a small flat head screwdriver. In my case, I'm using a small torque screwdriver. Put it in. Push it straight back, and you'll feel the spring. Push against the spring, and the airbag will come out. There's one on each side.
With the airbag out, there's three clips to remove. We push up on the clip. Same thing over here, pull up on the clip. With the clip all the way out, with a little black tab you've got to push in then and disconnect.
Now to remove the wheel, there's one bolt in the middle here. It's going to be a 24 millimeter. Impact gun is easiest, but you can get it with a wrench, too. Give the wheel a tap. You can remove it by fishing the wires through the back and then disconnect.
Now, there's a little bit of disassembly involved from the original wheel to transfer items over to our new R wheel. Now, as far as the trim goes, the R actually includes the matching R trim, which is a little bit of a darker, almost a smoked chrome versus the original. What we have to do is get all the switches off of here and then transfer them over. Start on the side here by removing two of the torque screws. Because we've got to remove it, start on the end and use a small pick if you have to, just get the plastic separated here and then disconnect from the back.
Now to remove the cruise control, we've got two more screws, one up here and one down below. This one, you may just want to flip it over. The clip's kind of hard to get to, but it's right in here. Then, unplug.
We're going to assemble one side at a time, so start by finding the correct matching GT350 piece here. What we're actually going to do is flip this over, unscrew it and transfer it over. Now, you don’t need to over-crank the screws. They don't ... The holes actually are not threaded, but they're just soft plastic, so the screws will cut into it as you put them in.
Moving over to our R wheel now, we're going to plug this one in first. Now, the top piece can go on. Now, you're going to do the same exact thing on the other side.
For the bottom piece here, all we need are the screws from the original. The wheel's ready to go back into our car.
We're going to start by fishing the airbag wires through the hole up here and then plug in the wheel. Make sure you line everything up. The harness should be in the center there. The two yellow tabs should be right there. With the wheel bolted down, make all the connections for the airbag. These are color coded, all yellow and black and yellow. You want to get it lined up with the springs. Push to re-install, and your installation is finished.
It was truly an honor for Ford to choose CJ Pony Parts to build this car for their Ford Performance Display at this year's SEMA Show. With high-quality Ford Performance parts, along with high-quality parts from Anderson Composites and COBB, we built a Mustang that we are truly proud of. If you're lucky enough to be attending this year's SEMA Show, make sure you check out the Ford display and come check out our Mustang.