Ford Tooling Lower Windshield Trim Pair 1987-1993

CJ's Part Number: WMT2
CJ's Low Price:
$20.99
1418774400 40188
Earn 20 RPM Points What's this?
WMT2
WMT2 WMT2_oncar Play Ford Tooling Lower Windshield Trim Pair 1987-1993 Video 1

Product Description

Pair of Ford Tooling Lower Windshield Trim for all 1987-1993 Mustangs.

This pair of black plastic lower windshield trim moldings are made from Original Ford Tooling for a perfect fit and finish. The moldings mount on the driver and passenger side lower portion of the windshield splitting the cowl vent grille.

Similar Mustang Parts

similar mustang parts More Mustang Moldings  

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a Review
Nice
These are very high quality repro with original tooling. Looks just like OEM even has the Ford part number stamped on it.
LANCE September 1, 2014
Great product
Perfect fit and look
Lower front June 12, 2014
2 Results

Product Video

By Bill Tumas: We recently replaced the cowl grill on our 1990 Mustang Convertible. It really cleaned up the front of our car, but unfortunately, sometimes, when you add new parts, some of the older stuff looks a little more worn out. We're noticing a lot of wear on our lower windshield moldings, so today, I'm going to show you how to replace those as well. For this installation, you'll need a Phillips head screwdriver, panel removal tool, and a small pick.

To remove the lower windshield molding, we have to remove our cowl first and then the outer pillar trim, as well. To remove the wiper, simply lift up on the arm, pull out the tab here. Press it back down and slide it off.Now, we're going to remove the six screws that hold the cowl to the body, lift up to move the washer hose, and put our cowl aside. We'll need to remove this thin windshield weather stripping to get this outer panel off. We want to get a small pick, go right down here in the corner, and pull it out.

You want to grab a panel removal tool, slide underneath the panel, and just twist to release. We don't have to take it all the way off. Now, we can access our molding. We're going to remove the original molding and you can just pop it off the clips. The lower windshield molding is held on by these two metal tabs. Many times the original plastic clips will be broken off. You want to remove them before you install the new panel.

We'll give the area a quick cleaning before we install the new pieces. To install the new molding, you'll align these two clips up, two metal tabs, put it in the center and press downward. At this point, you can reinstall your pillar. Taking a close look at ours, it's also pretty faded. Again, with the new part here, this will probably look pretty worn.

We're going to remove this the rest of the way, give it a quick coat of paint before we put it back on. Simply pull it outward, slide it down, and out. Give it a quick scuff with a Scotch Brite. Then I'll wipe it down with a little bit of rubbing alcohol. Let it dry for a couple minutes and be ready for paint. Now, we'll give it a couple coats of trim black.

We'll give that some time to set up before we put it back on the car. We're going to reinstall our new painted pillar piece and then we want to attach this weather stripping to the pillar before we press it down into place.

Once you've repeated the process on the other side, we're ready to reinstall our cowl. Please don't forget to hook up the washer hose. Again, you're screwing in the plastic here so make sure you make them snug but don't over tighten them. The last step, reinstall the wipers and our installation's finished.

New trim panels and a little bit of paint made a huge difference in the look of our Mustang. If you're just looking to replace the trim, you'll need about a half an hour of labor total. If you're going to paint like we did, I'd say give yourself an hour to do the whole job. You'll be back on the road in no time.