Pop-Open Fuel Cap Kit with the Running Horse Tri-Bar Logo for all 1970 Mustangs.
When you look at the fuel filler cap on your 1970 Mustang, do you like what you see? Or does your original one look like it's seen better days? If it's time to get a new fuel cap, then check out this Pop-Open Fuel Cap Kit from CJ Pony Parts!
Features & Benefits:
- Ford Licensed
- Running Horse Tri-Bar Logo
- External Pop-Open Cap with a Brushed Center and Chrome Outer Ring
- Swings Down and Reveals a Standard Twist-Off Fuel Filler Tube Cap
- Chrome-Plated Mounting Frame and Bezel
- Comes with Everything You Need to Upgrade to a Pop-Open Fuel Cap or Replace an Existing One
This Pop-Open Fuel Cap Kit features the famous Running Horse Tri-Bar Logo and is licensed by Ford. The external pop-open cap has a brushed center and a chrome outer ring and it then swings down to reveal a standard twist-off fuel filler tube cap! The included mounting frame and bezel both feature a lovely chrome-plated finish that's sure to turn heads! You'll get everything you need to upgrade from a screw-off type cap to a pop-open one or to replace your existing pop-open style fuel cap.
If your Mustang's exterior trim is missing or worn after years of exposure to the elements and road debris, CJ Pony Parts has many new parts waiting for you. Most original equipment is available, plus a few options not common to certain Mustangs, so you can really set your Mustang apart from the crowd.
Order a Pop-Open Fuel Cap Kit with the Running Horse Tri-Bar Logo for your 1970 Mustang from CJ Pony Parts today!
Product ReviewsWrite a review
I have a 1970 fastback with the honeycomb trim surrounding the gas cap, will this cap work for my car?
Hi, I am just wondering how much it is to post the 1970 Mustang pop open fuel cap to Australia Brisbane please?
This will be the second one I will order. The latch points on the cap are not well machined and the cap often pops off. If you try to adjust them they snap off. Will my replacement have this problem?
I have the pop open cap for the 1970 mustang just need inside parts are they sold seperate
Is this cap vented. I got a new gas tank from you but my old tank had all the California emissions on it. The new tank doesn't so It won't be vented. I saw that all the caps pre 1970 were vented. I have a 70 Mach 1.
You Might Also Like
CJ's Low Price:$103.99
CJ's Low Price:$106.99
These are all the parts that are included in pop open gas cap kit for the '69 Mustang. It actually gives you two options as far as how to mount it. The pieces over here for the original pop open style; if you want the look without the pop open function; they include a gas cap as well. We are going to show you how to assemble it before we install it on the car.
For this installation we used a regular Philips-head screwdriver, a small tip Philips-head screwdriver and a pair of needle-nose pliers.
The first step in the assembly is to mount the emblem. You'll line up the holes and press in. You will use the retaining washes and put them on the back to keep it in place. You will use the pair of needle-nose and crease them just slightly before you put them on so that they fit tight.
The next step is the spring. It's gonna go on the door right over the clips we just installed. I'm going to grab the cap itself. You want to put the washer in the center. Now put the screw in the center. Then, push down on it while tightening. Next, we'll install the gasket over the cap here. Make sure you line up the holes. Now we'll install the cap and the retaining screws. Now our cap is ready for installation.
Our '69 Mach 1 came with factory pop-open gas cap, but, like the rest of the car though, it could use a little bit of brightening and so we are going to install our new gas cap. The first step, pop open the gas cap and remove the retaining screws. Once you have all the screws out, grab the bottom and give it a little tug and it'll come right off. We are going clean it up a little bit before we put the new one on. We are now ready to install our new cap. The four screws on the outside were removed. This stud here is for a fifth screw that comes from the inside to make it so no one can steal your cap. We'll install the outside ones first. You can reuse the original hardware or we do offer new hardware as well. Now, you are ready to install the last screw from the trunk and our installation is complete.
Remember, if you chose to use the pop-open assembly, you do not use the gas cap that is included in the box. Our new pop-open gas cap really glows on the back of our otherwise original '69 Mach 1. You will probably spend more time assembling the cap then it actually takes to install it. Figure no more than 20 minutes for the whole process. You'll be back on the road in no time.