Holley Polished Aluminum 600 CFM 4-Barrel 4160 Series Carburetor with Electric Choke for all 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984 and 1985 Mustangs with a Carbureted Engine.
If you're looking for a new 4-barrel carburetor for your Sunday cruiser or street machine. Holley's all new Polished Aluminum 600 CFM 4-Barrel 4160 Series Carburetor with Electric Choke is the perfect choice.
The 600 CFM 4-Barrel 4160 Series Carburetor from Holley is calibrated for all-out street performance. This carburetor makes for a great replacement on stock to mildly modified Mustangs. Every Holley carburetor is 100 percent wet-flow tested before it leaves their facility in Bowling Green, Kentucky for "bolt on and go" performance.
Holley's 4160 Series carburetor is constructed from aluminum and features a beautiful polished finish that will look brilliant under any Mustang's hood. The aluminum construction results in a product that is 40 percent lighter than Holley's other carburetors that are constructed from zinc.
- Vacuum Secondaries Allow Use on Wide Variety of Vehicles
- Electric Choke for Easy Warm Up
- Single Feed Fuel Inlet
- 1 Timed (Spark) Port, 1 Full Vacuum and 1 PCV Port
- Universal Calibration for Easy Bolt-On Performance
- Made in the USA
*Does not work with AOD transmissions.
The carburetor on your Mustang is a part that you rely upon to work. Without it, your Mustang isn't going anywhere. That's why you want to make sure you get a high quality part when you replace or upgrade your carburetor, and no carburetor is going to have higher quality than the products from Holley!
Order a Holley Polished Aluminum 600 CFM 4-Barrel 4160 Series Carburetor with Electric Choke for your 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984 or 1985 Mustang with a Carbureted Engine from CJ Pony Parts today!
Similar Mustang PartsMore Carburetors
Product ReviewsWrite a review
I have a 66 mustang, the car starts easy and runs! But I have gas running from the bottom of the carburetor! Will gaskets help?
I have a standard Mustang with the same carburetor and I'm having a hard time idling, have to put idle real high in order for it to turn on. Once on I lower the idle and if I lower it too much it turns off.
There is a *footnote stating that the Holley 80457SA will not work with an AOD transmission. I currently have a stock C4 automatic in my 1965 Mustang but may upgrade to an AOD soon. Can it be converted to run with the AOD, & what (kit) would it take?thx
I have a pickup with a 1976 ford grand torino expolice car, what size a 4 bbl would work without csusing problems in idle and highway and street cruising??
I have a 1973 Ford Mustang 302 engine 5.0 I'm currently using two barrel motorcraft electric choke Will this carb fit right on or will their need to be adjustments?
I have a 64 98 Oldsmobile with a 394 I wanted a 550 I need one that will fit
Hi, I have a 71 mustang with a 351 Cleveland and it has a manual choke on a 4 barrel carb. Curious what difference is between manual and electric choke. Other parts I'd need to get?
I have a 66 mustang 289 with autolite 4100 carb. Will this replace it? do I need any installation gasket kit? Do you have any other carb that can replace my 4100
You Might Also Like
CJ's Low Price:$301.95
CJ's Low Price:$353.95
CJ's Low Price:$323.95