Hood Molding Polished Aluminum 1969

CJ's Part Number: HM3

Regular Price: $28.99

Special Price: $20.29

1490745600 17914
When installing this hood molding you might want to finish off the front end with the items listed below.

Regular Price: $38.99

Special Price: $29.24


Regular Price: $38.99

Special Price: $29.24

CJ's Low Price:
Earn 20 RPM Points What's this?
1490054400 1490918400
On Sale: Up to 30% Off Sale!
Hood Molding Polished Aluminum 1969
Hood Molding Polished Aluminum 1969 Play Hood Molding Polished Aluminum 1969 Video 1

Product Description

Polished Aluminum Hood Molding for all 1969 Mustangs.

The front end of your 1969 Mustang can see its fair share of damage due to road debris. Replace your hood molding and replace it with this quality reproduction today. This reproduction hood molding will work on all 1969 Mustangs. The hood molding is constructed out of aluminum which is polished to give the look of chrome.

- Polished Aluminum Hood Molding
- Hood Molding Clips (6)
- Mounting Nuts (6)

- Works on 1969 Mustangs
- Original Style Hardware
- Built in Molding Clip Channel
- Quality Polished Finish

Please Note: This hood molding will not work on the 1969 Shelby Mustangs.

This hood molding gets mounted on the front edge of the hood with the supplied hardware. It comes with six hood molding clips that protrude though the hood of you 1969 Mustang and securely holds the hood molding in place with the mounting nuts. The hood molding has a built in channel that allows the molding to be fine-tuned for ideal fitment.

Your exterior trim may look just awful after many years on the road. Mustang chrome can become faded and pitted, while the rest of the Mustang trim can crack and fade. Thankfully, CJ Pony Parts has hundreds of Mustang exterior trim parts available so you can fix and upgrade these problem areas, making your Mustang look like new again.

 Purchase a new Polished Aluminum Hood Molding for your 1969 Mustang from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Mustang Parts  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
Hood Molding Polished Aluminum 1969 is rated 2.6 out of 5 by 7.
Rated 2 out of 5 by from hood moulding poor stamping, this moulding was 1/2 inch of center and the finish does not look like the original moulding.
Date published: 2015-05-19
Rated 5 out of 5 by from Fits my 1969 Mustang coupe perfectly-buy confident Was a little worried after reading the reviews but there is such a price difference between the reproduction and the "Ford tooled" versions that I went ahead and purchased - keeping my fingers crossed. I am pleased to say this fits the car perfectly. The biggest thing you have to get right is the direction of the attaching bolts. Make sure the "spring" part of the attaching bolt is facing up. If you put the bolts in upside down, the molding will mount far lower on the lip of the hood.
Date published: 2016-05-19
Rated 1 out of 5 by from Poor fit I wish I had read the review when I ordered it, 'cause the fit is so bad. It doesn't at all run along the edge of my hood and since it's so thin material it gets very easily bent. I live in Denmark, so there is no point in returning it, but I'm probably gonna order the Ford Tooling one, though it's 4 times as expensive.
Date published: 2015-06-19
Rated 2 out of 5 by from hood trim The first piece I bought was bent wrong, the second was bent correct but the finish is dull and the aluminum has a lot of manufacturing scratches. Its better than a beat up original piece. Pearly a driver quality piece, know where near show standards.
Date published: 2015-08-06
Rated 1 out of 5 by from Poor Fitment I purchased this hood molding and it did not fit well. The finish in my opinion was good but did not look original. The width was slightly longer on one side than the other. The center bend was the worst part of the piece.
Date published: 2016-06-06
Rated 2 out of 5 by from No way No matter how you try it is too short and does not bend into shape correctly.
Date published: 2016-02-07
Rated 5 out of 5 by from Awesome fit ! Good Quality, Grat price. High quality trim piece, easy installation, perfect fit !
Date published: 2015-11-15
  • y_2017, m_3, d_28, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_HM3, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 24.52ms

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 121.37ms
  • bvseo-msg: HTTP status code of 404 was returned;

You Might Also Like

Product Video

Hood Molding Polished Aluminum 1969 Video Transcript
By Bill Tumas: We’re here with a reproduction hood molding fitting your 1969 Mustang. This is a reproduction of the original 1969 hood molding found in the factory hood of all 1969 Mustangs. It's correct to the original with the correct flaring on the edges and has all the mounting hardware with the rubber bushings and nuts included. This hood molding and other moldings for your 1969 Mustang are available here at cjponyparts.com.