Mustang Ford Racing Bullitt Pedal Cover Set (1994-2004) Installation Instructions

Tools Required:
  • Mirror
  • 13mm Socket & Extension or Deep Socket
  • Socket Wrench
  • Tongue and Groove Pliers
  • Thin Flat Head Screw Driver
  • Stubby Flat Head Screw Driver
  • Flat Head Screw Driver
Install Difficulty:
  • Easy
  • Easy Project
1. The stock pedal covers in need of replacement with the new Mustang Ford Racing Bullitt Pedal Cover Set.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
2. Gather the required tools.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
3. Remove the old dead pedal Mustang pedal pad by prying it off the metal bracket near each of the two clips using your flat head screw driver.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
4. Put the new Mustang Ford Racing dead pedal in place, making sure the clips are in the holes just enough to hold it in place, then sit in the driver's seat and push down with your foot until you feel and hear each clip snap into place.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
5. To prepare for the new Mustang Ford Racing Bullitt brake/clutch pedal covers, remove the old clutch and brake pedal covers by just peeling them off by hand. Mine were ripped, so they came off very easily. If yours are in better shape, you may need to pry them off with your flat head screw driver.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
6. Soak the new Ford Racing clutch pedal cover in hot water for several minutes.
7. Immediately after removing the clutch pedal cover from the hot water, slip on the bottom, narrower portion. Because of the shape of the pedal, I found it a little easier to get the bottom on first. Then, with the help of your flat head screw drivers, pry the new pedal cover onto the pedal. This is more difficult than you would expect, and will take some time and patience.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
8. Repeat steps 6-7 for the brake pedal cover. It is exactly the same as the clutch pedal cover, except it's a little harder to do since the brake pedal is closer to the floor than the clutch pedal is. That's when having a stubby flat head screw driver comes in handy.
9. Using a mirror, make sure that the rubber from the clutch and brake Mustang pedal pads is over its respective pedal all the way around. If there are small sections that are still tucked in, wedge your skinny flat head screw driver between the rubber cover and metal pedal and pop the tucked in portion out and over the pedal.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
10. Moving on to the accelerator pedal, remove the two nuts (circled in green) holding the accelerator pedal assembly to the firewall. You will need a socket wrench and a 13mm socket with an extension, or a deep 13mm socket. At this point, you may either remove the throttle cable (circled in red) from the accelerator pedal arm so you can remove the assembly from the vehicle, or just leave it connected and work on it in the vehicle like I did.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
11. Pull the accelerator pedal assembly away from the firewall, taking care not to over-extend or twist the throttle cable, and turn the accelerator pedal over. Use your tongue and groove pliers to pop out the pin holding the pedal to the arm, and remove the old accelerator pedal.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
12. Line up the new Mustang Ford Racing accelerator pedal holes with the holes in the arm, and stick the retaining pin in to hold it in place. Using your tongue and groove pliers, insert the retaining pin the rest of the way, taking care not to damage the new pedal in the process.
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
Mustang Ford Racing Bullitt Pedal Cover Set Install Image
13. Now that your new accelerator pedal is attached to the arm, all that's left to do is bolt the arm back to the firewall. If you removed the throttle cable from the arm in step 9, now would be the time to reattach it.
14. Your installation is complete. Enjoy the added grip and good looks of your new Mustang Ford Racing Bullitt Pedal Cover Set!
Mustang Ford Racing Bullitt Pedal Cover Set Install Image