JLT Cold Air Intake Kit for all 2012-2013 Boss 302 Mustangs and 2011, 2012, 2013 and 2014 GT Mustangs that have Upgraded to the Boss 302 Intake Manifold.
Looking to add a boost in horsepower in your 2011, 2012, 2013 or 2014 GT Mustang with this cold air kit from JLT Performance. This kit from JLT replaces your boring factory air box, with a brillant color match cold air intake which will look great under the hood of your Mustang. You will see horsepower gains close to 24-30 horsepower to the rear wheels. This heat shield has a direct duct from the fresh air inlet to the filter as well as a smooth wrap around exterior.
- JLT textured plastic or painted plastic intake tube with PCV fitting and integrated 107mm MAF housing
- 3" Silicone coupler
- 4-1/2"x9" S&B powerstack air filter
- ABS plastic heat shield with weatherstrip
- Clamps and hardware
- Sound tube cap
- Necessary fitting for automatic transmission Mustangs
*Requires a tune after installation!
The two digit code after each color name in the drop down menu is the Ford paint code. Please verify your Mustang's paint code prior to ordering. CAK120 is a lightly-textured molded black plastic finish. CAK120UA is a smooth painted black finish. All painted tubes go through an in-depth process to remove texture, only the best quality materials are used to give each tube a smooth gloss finish.
If you're looking for some of the best cold air intakes and performance parts for your Mustang, go no further than CJ Pony Parts' selection of parts from JLT Performance. With more than several 2011-2014 Mustang parts available, you can find exactly the cold air intake you need for your performance Mustang-just check out the selection of JLT Performance parts from CJ Pony Parts today
Similar Mustang PartsMore Mustang GT Cold Air Kits
You Might Also Like
CJ's Low Price:$429.99
CJ's Low Price:$539.99
CJ's Low Price:$195.99
CJ's Low Price:$614.99
JLT Cold Air Kits are available in this carbon fiber finish, black textured plastic, they are also available painted to match the OEM paint on your Mustang. They come with these pre-oiled, reusable S&B power stack filters, include all you need for installation, including heat shields where applicable.
JLT oil separators are a great modification for a supercharged car. They also work really well with naturally aspirated cars as well. They catch oil, stop it from going back into your intake track due to crank case pressure. They're available in both the black or silver finish and come with factory Ford lines making them an easy installation.
In this installation, you'll need a 3/8-inch ratchet, 13-millimeter socket, 10-millimeter socket, six-inch extension, flat head screwdriver, Phillips head screwdriver, T20 torx bit, small pick and pliers.
This is JLT's cold air kit for a 2011 to 2013 Mustang that we're going to be installing on this 2013 GT convertible. The first step is to connect a coupler and the air filter to the intake tube. Now we're ready to remove our factory cold air kit. To get to the clamp down here, the intake cover is going to have to come off. In the case of our premium car, strut tower braces are in the way, we're going to have to remove that first. Now I'm going to remove the intake cover by simply pulling upward. Now remove the factory intake sound tube. Before the air tube comes off, we have to disconnect the PCV. Put pressure on the little gray clip upward and slide it off.
We're going to remove the hose clamps for the main inlet tube. Before we can remove the air box, we got to disconnect the mass air sensor. It's a little red tab underneath, slide it back, slide the sensor off. Now we can remove our air box. I'll remove the front part of the box by simply pulling straight back. Now we're going to install the JLT supplied shield. It's going to mount to the stud for the front of the air box and, for the back of it, put it right where the factory bolt was removed from. The last thing we need to do before we can install our new kit is to take the factory mass air sensor out of the original housing. I'm going to use the hardware provided by JLT with the kit and we're ready to install it.
Put it in place and slide the tube over our throttle body. I'm going to make two more connections. Reconnect our sensor. The last step is to reconnect our PCV.
While the new JLT intake does have provisions to hook up your sound tube, we found that JLT sounds good enough on its own, so this really isn't necessary. JLT provides the block off plate for your firewall as well as to block off the intake itself if you're not using the factory sound tube.
Notice our JLT intake kit looks a hell lot better than the stock air box. It's going to make some serious power too. Due to the increase in airflow, you want to pick up SCT XCAL tuner as well. Expect to see about 20 to 30 horsepower, installation no more than 30 minutes. You'll be back in the road in no time.