MBRP Aluminized Series 4" Single Side Exit Cat-Back Exhaust System with a 5" Tip for all 2015, 2016 and 2017 F150s with a 2.7L or 3.5L EcoBoost Engine.
After picking up your 2015-2017 2.7L/3.5L EcoBoost F150, one of the major complaints of any enthusiast is the quiet, restrictive exhaust. Open up the airways of your F150 and get the exhaust note you want with MBRP’s new Aluminized Series 4" Single Side Exit Cat-Back Exhaust System with a 5" Tip for 2015-2017 F150s with a 2.7L or 3.5L EcoBoost Engine.
Adding a cat-back system to your F150 is the perfect way to add horsepower and torque and a head-turning exhaust note while complimenting your other modifications. This (S5259AL) exhaust system is 4” in diameter, is manufactured in durable aluminized steel and will exit through a single 5” mirror polished tip behind the passenger rear tire of your 2015-2017 F150.
Features and Benefits:
- Made With Aluminized Steel
- Over 70% Increased Exhaust Flow
- Single Side Exit With 5” Mirror Polished Stainless Steel Exhaust Tip
- Measurable Increase in Horsepower and Torque
- Bullet Style Muffler
- 4” Diameter Exhaust Tubing for Maximum Flow Velocity
- Fits all Cab and Bed Configurations
- All Necessary Hardware and Installation Instructions Included
*This cat-back exhaust system will not fit 2017 Raptors.
This exhaust system from MBRP is proven to be one of the best in the industry from almost any corner you look at it. Why, you ask? MBRP puts countless hours on the dyno and hundreds of miles on the street and track to perfect. This system is designed to deliver a head-turning exhaust note without making your ear drums ring on the highway, while allowing for maximum exhaust flow to give you the best performance numbers out there. Made of durable and reliable aluminized steel, this system minimizes exhaust temperatures through its seamless sealed construction. Seals are a major point of rust on any budget exhaust system, so MBRP designs their systems with as little seams as possible.
The stock F150 cat-back sees 477 CFM but MBRP's (S5259AL) cat-back flows 877 CFM. With an exhaust flow increase of over 70%, you can expect great gains in both horsepower and torque. Installation of the MBRP 4" Side Exit Cat-Back Exhaust System is relatively easy, needing only a few hand tools to complete.
Please Note: Extension pipe will need to be cut, or not be needed at all for some cab and bed configurations. Shortening of the front pipe will be required to fit smaller wheel wheelbase configurations. Please refer to installation instructions.
The EcoBoost engines available on the 2015-2017 F150 make minimal noise from the factory. If you want to hear the turbo(s) better, then picking up this MBRP Cat-Back Exhaust System is the perfect choice. These systems pump up the decibels without making your ears ring. The exhaust notes are subtle and manageable when cruising down the highway but will roar when you mash on the throttle. Given all the pros of this system from MBRP, how do you say no to throwing this exhaust on your F150?!
So what are you waiting for? Order a MBRP Aluminized Series 4" Single Side Exit Cat-Back Exhaust System with a 5" Tip for your 2015, 2016 or 2017 F150 with a 2.7L or 3.5L EcoBoost Engine from CJ Pony Parts today!
Similar F-150 PartsMore Cat Back Exhausts
Product ReviewsWrite a review
doe this come only in aluminum?
Can I get this set up with a Black Tip?
Will it fit a singel cab short bed
Will this fit the 3.5L non turbo? Thank you
You Might Also Like
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$749.99
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$699.99
MBRP Cat-Back Exhaust System 3" To Dual 2-1/2" Split Side Exit Aluminized Series EcoBoost 2.7L/3.5L F-150 2015-2017/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$439.99
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$280.00
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$129.00
For this installation, you'll need a jack and jack stands or a lift, 3/8" ratchet, 13mm socket, 15mm socket, 5/16" hex key, and a 15mm wrench.
We're obviously going to start by removing the factory system. It's pretty easy to remove, there's only three things we have to loosen; two bolts up here on the flange, and then one clamp right here, with one nut. The two bolts that we have to remove from this flange are 13mm. Remove this clamp by loosening the 15mm nut. There's a locking tab on this muffler here. You have to give the pipe a twist to release it. Now we can remove the exhaust system. It can come out as one piece, but you might want some help because it's pretty heavy. I have my assistant Bill here, you might recognize him, he's been in a couple CJ's videos before. We're going to pull this exhaust out together. There's a total of four hangers that you're going to have to remove. This first one up here can come off by itself. Penetrating lubricant is going to help a lot when removing these. Spray it on the rubber here, and these hangers should come out really easy. Now that there's only three hangers left installed, we can just pull the exhaust out of them.
Now that the factory exhaust is out, we can install our new MBRP Cap Back. There's an extension pipe included in this kit, if you have a longer wheel base truck. Since our truck is a short bed, we don't need it, we can install just using this front pipe. We're going to be using the supplied hardware to secure this front pipe, with a bolt and washer on one side, then a flat washer, lock washer, then a nut on the other side. Just get these hand tightened, you don't want to tighten this completely down just yet. Next, we're going to install this exhaust clamp with a built in hanger, and secure it to this rear mount. Install the muffler with the MBRP logo facing upright. Now, just get these hand tight for now, you don't want to crank these down just yet. The next pipe to install is this over-axle pipe. Get this clamp hand tight. Now we can install the tailpipe. Once you have everything installed properly, you can go ahead and start tightening up your clamps. All that's left now is just the tip. You want to get this on to where you like it, whether it's further out, further in, or clocked a certain way, whichever position you like, and then tighten it down. Tighten it up with a 5/16" hex bit. Now your installation's finished.
Now, for the moment we've all been waiting for, let's hear what it sounds like. You've heard what it sounds like on the outside already. You're probably wondering what does it sound like on the inside. It is loud? Is it quiet? Does it sound good? Does it not sound good? Does it sound like a V8, sound like a V6, what does it sound like? First impression, it's really quiet in here actually. At idle, you can't really tell that there's an exhaust. I have the radio off and you can barely here it at idle, it's really quiet. For cruising, we're at highway speeds right now, 55 miles an hour, and you can barely tell that there's an after-market exhaust back there. It's really quiet and I really like it. It doesn't drone. It's not going to kill your ears. It's not going to be exhausting if you go on a long cruise, road trip, vacation, whatever. It's not going to kill you, and it's not going to get you a ticket either for being too loud. This thing is pretty quiet. When you get on it, you open it up, it's a lot louder. You can hear the turbos. It sounds pretty good, but even then, it's still not obnoxiously loud. It sounds good. IT's the perfect mixture of just being loud enough and sounding good. It's not overkill at all. I think it's just right.
If you're looking for that V8 sound, you're not going to get it with this. That's just not what this is supposed to do, but it does sound great. It's a different kind of sound. It's unique. There's not many things on the road that sound like this. There aren't many twin turbo V6s out there. There's plenty of V8s, you can hear them all day, but this is a very unique sound. Overall, I think this exhaust was a really good choice for this truck. It's not overkill. It's not going to kill your ears. It's not going to get you a ticket. It's not going to make anyone mad with how loud it is. It's not loud at all. It's nice and quiet for an after-market exhaust. It sounds great, and it runs great. I really like this exhaust.
Our MBRP exhaust is installed. It fit great. It looks great. It sounds even better. Installation should take one to two hours, and before you know it, you'll be heading down the road.