MRT Black Hood Strut Kit for all 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 and 2004 Mustangs.
Get rid of your factory prop rod on your 1994-2004 Mustang and install MRT Hood Strut Kit today. This hood strut kit is a direct replacement for all 1994-2004 Mustangs with a factory hood. When installing this hood strut kit from MRT you will notice that the hood will open with little to no effort. This strut kit provides you with extra room under the hood making it easier to work on the engine or detail it for shows.
- Eliminates the Factory Prop-Rod
- Reuses Original Attachment Points
- Available in OEM Paint Colors
- Bolt In Installation
- Easy Installation
- Made in America!
Please Note: MRT hood struts were designed for use with factory hoods and may not work with some aftermarket hoods.
These hood strut kits from MRT feature a strong steel body with a heavy duty gas struts. The steel bodies from MRT can be painted to match the exterior paint on your 1994-2004 Mustang. The black painted finish is not a match to the original paint.
MRT makes this easy to install making it a direct bolt in installation. The MRT hood strut kit reuses the original factory attachment points. It's very easy to install, all you'll need is a 10mm wrench. Unlike other kits available, MRT hood struts require no drilling for installation.
If you're looking for the latest styling and performance parts for your Ford Mustang, you have lots of major brands to choose from. However, few offer the same experience and proven results as MRT. CJ Pony Parts offers the latest styling and exhaust performance products from MRT, giving you lots of choices from one of the leading and most trusted retailers in the aftermarket.
Purchase a new MRT Hood Strut Kit for all 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 and 2004 Mustangs from CJ Pony Parts today!
Product ReviewsWrite a review
You Might Also Like
CJ's Low Price:$204.99
Regular Price: $224.99
Special Price: $157.49
The hood strut kit comes with six pieces, two struts, left and right-side hood brackets that are stamped, matching fender brackets, and detailed instructions. For this installation you'll need a quarter-inch ratchet, an eight millimeter socket, 10 millimeter socket, and if you need to remove the struts for any reason a small flathead screwdriver.
We'll be installing our MRT Hood Strut kit on this 1996 Mustang Cobra. Let's get started. Thankfully, this should be the last time we ever use this. We're going to start by installing the bracket on the fender. To do that, you'll need to remove this rear bolt. You want to make sure you grab the bracket labeled properly for the side of the car you're working on, in our case the right-hand. Place the bracket over the fender hole, make sure the stud for the strut is in the front, and tighten down the factory's bolt. Now we're going to install the bracket on the hood side. Step one, remove the nut from on the top stud. You want to loosen the lower nut just enough to get the bracket to slide underneath it. You want to make sure you keep the hood pressed down on the bracket, then you want to re-tighten the lower. Now we want to reinstall the top.
Now we're going to install the strut itself. You want make sure you install it with the body upward to make sure no water condensation gets inside the strut. Press it up against the ball and just push, it'll pop into place. In some cases, the strut might be a little below the stud. In that case, you'll just have to lower the hood down slightly to be able to press it on. Put our prop rod down, bring the hood and snap it in place. Now you want to repeat the process on the other side.
The last step is we're going to remove your factory prop rod. Since we never removed our hood from the hinges, there should be no alignment issues. Just to make sure, we're going to slowly pull our hood down to make sure that it lines up properly. Good on that side. Good on that side. Pull it up again. See with our hood struts how nice and easily the hood goes up.
The hood struts are a nice easy to install upgrade. Not only does it do a better job supporting our hood, it gets rid of the prop rod so if you're working on the engine it doesn't get in the way. The installation should take you no more than half an hour and you'll be back on the road in no time.