Mustang Ford Racing GT 85mm Cold Air Kit (2005-2009) Installation Instructions

• 
• 
• 
• 

2005-2009 Mustang GT Ford Racing 85mm Cold Air Kit

This 85mm Cold Air Kit from Ford Racing will fit 2005-2009 GT Mustangs.

Replace the stock cold air kit with this high quality upgrade from Ford Racing! The 85mm Cold Air Kit will fit any 2005-2009 Mustang GT and is 50 state legal. When using 91 octane or higher fuel, you'll easily experience a 20 horsepower increase. Also comes with a voucher for a Ford Racing ProCal tool.

This Install Also Applies To:

• Mustang Steeda Cold Air Kit GT 2005-2009
• Mustang GT Straight Shot Cold Air Kit MAC 2005-2009
• Mustang Steeda Cold Air Kit V6 2005-2009
• Mustang BBK Cold Air Kit Silver 4.6L 3V 2005-2009
• Mustang BBK Cold Air Kit Chrome 4.6L 3V 2005-2009
• Mustang BBK Cold Air Kit Charcoal 4.6L 3V 2005-2009
• Mustang BBK Cold Air Intake Kit V6 2005-2010
• Mustang JLT Cold Air Intake Kit Series 2 V6 2005-2009
• Mustang Roush Cold Air Kit V6 2005-2009
• Mustang Roush Cold Air Intake Kit GT 2005-2009
• Mustang Steeda Cold Air Intake Kit High Velocity Pro-Flow Black GT 2005-2009
• Mustang JLT Cold Air Kit Series 3 GT 2005-2009
• Mustang Airaid Cold Air Intake Kit MXP Series With SynthaFlow Filter GT 2005-2009
• Mustang Airaid Cold Air Intake Kit MXP Series With SynthaMax Filter GT 2005-2009
• Mustang Airaid Cold Air Intake Kit MXP Series With Blue SynthaMax Filter GT 2005-2009
• Mustang C&L GT Cold Air Intake System 2005-2009
• Mustang C&L GT Cold Air Intake System With Xcal Tuner 2005-2009
• Mustang C&L V6 Cold Air Intake System 2005-2009
• Mustang Steeda Cold Air Kit GT 2005-2009
• Mustang Ford Racing Cold Air Kit 85mm V6 2005-2009
• Mustang Power Pack With SCT X3 Tuner And JLT Cold Air Kit GT 2005-2009

Tools Required:

• Flat Head Screw Driver
• 8mm, 10mm, 15mm Sockets
• Ratchet
• T20 Torx Bit

Install Difficulty:

• 
• Moderate Project

1. To begin installing your new Mustang Ford Racing M-9603-GTB 85mm GT Cold Air Kit, pop your hood and locate your stock air intake. Disconnect your battery.

2. Locate the mass airflow sensor on the stock intake tube and unplug it, then use your Torx bit to remove it completely. Disconnect the PCV line and loosen the only bolt that is holding the air box to the fender. Loosen the intake tube from the throttle body with a flat head, then remove the old Mustang GT cold air kit.

3. Put the new Ford Racing cold air kit in place and use the bolt that was removed earlier to attach it. Then, use the new stud that came in the kit to attach the heat shield. Reinstall the MAF sensor into the new intake, along with the PCV hose that was removed earlier. Using your flat head screw driver, tighten all of the hose clamps on the throttle body as well as the air filter. The physical installation of the cold air kit is now completed, but it needs tuned with your Pro Cal.

4. Connect the Pro Cal to your Mustang via the OBDII port, which is located under the steering wheel. Select your tune from the menu and adjust the options to fit whatever additional mods you may have on your car. Once you have adjusted all of your options, program the car. Once programming is complete, remove the Pro Cal and start your car. You should let it idle for 5 minutes after tuning, so it can relearn everything again. The installation of your new Mustang Ford Racing 85mm GT Cold Air Kit is now complete!