Power Window Kit With Crank Handle Switches Bronco 1968-1977

CJ's Part Number: 76697236
CJ's Low Price:
$644.99
1480896000 66552
Make sure you also get a pair of new window crank handles and a master switch kit to install with your new power window kit!
CJ's Low Price:
$16.99
Qty
CJ's Low Price:
$44.99
Qty
Earn 644 RPM Points What's this?
Power Window Kit With Crank Handle Switches Bronco 1968-1977
Power Window Kit With Crank Handle Switches Bronco 1968-1977 Power Window Kit With Crank Handle Switches Bronco 1968-1977 Power Window Kit With Crank Handle Switches Bronco 1968-1977 Play Power Window Kit With Crank Handle Switches Bronco 1968-1977 Video 1

Product Description

Power Window Kit With Crank Handle Switches for all 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976 and 1977 Broncos.

If you want to maintain the factory look of your classic 1968-1977 Bronco without sacrificing the ease and convenience of power windows, we've got the perfect kit for you! This Power Window Kit has everything you need to convert your manual windows to power windows while also allowing you to reuse your original window cranks!

Features & Benefits:
- For Use with 1968-1977 Screw-On Style Window Cranks
- Converts Your Manual Windows to Power Windows
- Allows You to Reuse Your Original Window Cranks to Maintain the Factory Look
- Regulators are Made in the USA and are Made Out of 1018 Cold Roll Steel
- Regulators Have Bronze Oilite Thrust Bearings at All the Pivot Points
- Regulators Also Have Treated Gear Plates for Longer Teeth Life
- Regulators are Designed to Directly Bolt into the Original Mounting Holes with Little to No Modifications
- Regulators Use the Original Glass Channels and are Equipped with a New AC Delco OEM Motor
- Motor is Attached to Regulator to Make Installation Easier and More Convenient
- Power Crank Handle Switches are Controlled by Pushing Down and Pulling Up on the Crank Handle to Raise and Lower the Windows
- Handle Switches Mount Behind the Door Panels
- Original Cranks Mount Directly on to the New Power Crank Handle Switches
- Wiring Harness Includes Labeled Wires for Correct Positioning and is Fused for Proper Operation of Windows without the Engine Running

This Power Window Kit With Crank Handle Switches is for use on 1968-1977 screw-on style window cranks. The regulators will fit all 1966-1977 Broncos, but the crank switches will only work on 1968-1977 Broncos. The regulators are made out of 1018 cold roll steel right here in the good old U.S. of A. and feature bronze Oilite thrust bearings at all of the pivot points. The regulators also have treated gear plates, which means they'll have a longer teeth life. You'll use the original glass channels for your new regulators too. Both regulators come with a new AC Delco OEM motor that's already attached, which will make installing them even easier than it already is!

You'll control your new power crank handle switches simply by pushing down on the crank handle to lower your windows and then pulling the crank back up to raise them. The new handle switches mount behind your door panels so you can mount your original window cranks directly onto them, and the placement is up to you. There's no right or wrong way to position them! The regulators are specifically designed to directly bolt into the original mounting holes, which means there will be few (if any) modifications needed.

Finally, the included wiring harness has labeled wires for correct positioning, and it's fused so you can raise and lower your windows without the engine running!

This Kit Includes:
- Two (2) New Power Regulators
- Two (2) New AC Delco Power Window Motors
- Two (2) Power Crank Handle Switches
- One (1) Complete and Labeled Wiring Harness
- Two (2) Conduits

Please Note: The regulator will fit 1966-1977 Broncos, but the crank switch is specific to 1968-1977 Broncos.

Order a Power Window Kit With Crank Handle Switches for your 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976 or 1977 Bronco from CJ Pony Parts today!

Similar Bronco Parts

similar Bronco parts More Window Motors  

Installation Instructions

Mustang Installation

Bronco Applications

This product will fit the following Ford Bronco years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 171.36ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 95.55ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

Power Window Kit With Crank Handle Switches Bronco 1968-1977 Video Transcript
By Bill Tumas: You may be wondering, why do we have a Bronco in our studio today? Well, recently we installed a set of power windows on the boss' '68 Mustang coupe, and he was so happy with the results, he asked if we could install a set in this '68 Bronco that he's building for his son. So today, I'm going to show you how to install power windows in your classic Bronco.

This kit is very similar to the Mustang kit we installed, in that the power motor is already mounted to the regulator, making for an easier installation. It includes these switches that have threads that will fit a stock crank. That way, you're not using an after-market power window switch. Simply push the crank up and down. That'll make your windows go up and down. The kit includes both sides, two switches, and all the wiring necessary for installation.

For this installation, you'll need a Phillips head screwdriver, 1/4" ratchet, 3/8 socket, pick, marker, drill, 1/8" drill bit, 13/64 drill bit, 7/8 Uni bit, wire crimpers, wire strippers, in-line fuse, test leads, some extra primary wire, flashlight, and safety glasses.

Well, obviously, we know how to do this on a Mustang. I can't say I've ever done it on a Bronco before. So we're going to start by pulling off the door panel and taking a look at how the window works, then start taking it apart. We're going to start by rolling the window up, so we can see the channel. Here's where the regulator actually connects to the channel, which puts the window up. We're going to disconnect the roller between the regulator and the channel. That will allow us to separate the two of them. There's a little clip on the back side. Separate the regulator from the window.

Now, with the regulator separated from the window channel, we're going to remove the four screws that hold the regulator to our door. Now, we're ready install the regulator and motor assembly. You may notice, we cut this piece out here. It wasn't cut in the introduction, but we found with the new style switches this will have to be cut out for proper clearance. All models that ship from now on will have it cut out, so you won't have to worry about it.

Put the bolts in hand tight just to hold everything in place. Now, I'll tighten everything up. The mounting screws for this switch are actually located on the back side of the switch. We're going to remove those first. Now, we're going to remove the back of the switch so we can use it as a template for drilling our holes. Now, carefully remove the back, and place the switch aside. Now, we're going to line this up. This hole here in the back is where the actual piece comes through to connect our crank to, so we want to get that pretty much in the center.

Now, we'll reassemble the switch. We're going to install the wiring harness before we put the switch up into our door. Start on the inside of the switch. It's going to be the power, the ground, and then the motor wire on each side. So red, black, and then the brown or blue. It does not matter which side the brown or blue wires go to. Now, we're ready to install our switch. We'll leave the wiring harness dangling and put it up into place. Now, we're going to install the plug onto the power window motor.

Now we need to lower our regulator down so that we can reconnect it to the window channel itself. To do that, we'll grab some test leads, connect to our battery, and connect power to our switch so we can move the regulator up and down. You want to make sure your test leads are clear of the regulator when you move it up and down. And you want to get it pretty much right in the middle. Now we can install the roller. We're going to bring the window channel down into place. We'll put some new grease in there before we install the roller. And you want to put the roller actually in the channel itself, and then move it down to the regulator, and pop the regulator in. Now we'll test our window. We can keep the wires clear. It goes up nice, and it goes down.

Now we need to run the wiring from our switch inside our Bronco. How you do that kind of depends on how you're going to use your Bronco itself. In our case, our doors are fixed nut and are not going to come off, so we're going to use the supplied grommets and fish the wires through. If you do remove your doors, I recommend a paintless harness contact kit that can be installed in the door jamb, and that way you can remove the door without damaging your switches.

We're going to start by removing the strap for our door that will allow us to open the door a little bit further, making it easier to drill. The wiring harness is going to come through the bottom of the door here, and then go up, and that side's going to go on the top there. You just want to roughly eyeball up where it's going to go, then we can drill our holes. I'm going to start with a pilot hole first. Same thing over here. Now, we'll open the holes up. Now, we're going to fish the wire from the door, through the supplied grommet, up into the fender, and then out in the engine bay. I'll reconnect the strap to our door.

We let the wire fish into the back of the fender, then up through the dash, and out into our engine bay. Now, we're going to start fishing it over towards the battery. Since we're out of wire at this point, it's a good time to connect our in-line fuse. Now, we'll fish some wire from our starter solenoid over to our fuse. Now, we'll terminate this end of the wire, and we'll connect it to the power coming off our starter solenoid. We'll install our fuse and we'll check our windows. Put that up. It moves freely. Nothing's binding up. We're ready to reinstall our door panel. We're going to repeat the process on the other side, and your installation is finished.

Our power window kit fits great, and actually wasn't that bad to install, either. Expect to spend about three hours. You'll be back on the road in no time.