Powermaster High Mount Alternator Relocation Bracket Kit with Natural Finish for 1986, 1987, 1988, 1989, 1990, 1991, 1992 and 1993 Mustangs with a 5.0L Engine.After deleting all those unwanted horsepower draining accessories, finding proper mounting for the alternator can be troublesome. Thankfully, Powermaster created a mounting kit so you can run the alternator off just the water pump and crankshaft pulley. The kit will mount a two bolt straight mount Ford alternator on a 5.0L engine. A counter-clockwise water pump must be used. Replacing the tensioner is an adjustable sleeve with spherical rod ends so no movement occurs. The kit's extra tough design ensures proper belt alignment in the harshest conditions. High strength aluminum holds the alternator securely in place for optimum belt alignment.
Powermaster's alternator relocation bracket kit is extremely helpful whether underhood space is needed or you just want to rid your Mustang of the smog pump, power steering and air conditioning. Keeping the alternator in its general position on the engine means the whole driver's side of the engine will be open. Whether you want to add a turbocharger, supercharger or just clean up your engine bay, Powermaster's alternator relocation kit is the best way to achieve the look you want.
Equip the 5.0L engine in your 1986-1993 Mustang with precision engineered parts from Powermaster. Not only do Powermaster parts dress up your engine, but they function as well as they look.
Available with a natural or chrome finish.
Product ReviewsWrite a review
does this work with under drive pulley
What is the belt length used for this setup as pictured?
i have a 90 foxbody. with twin turbos. im running into an issue with clearence on the passenger side where alternator is. my question is will this kit move alternator towards the center or even if it just moved over towards the diverers side about an inch
Will this kit mount on the top driver side?
You Might Also Like
CJ's Low Price:$125.99
From:CJ's Low Price:$329.99
CJ's Low Price:$48.99
Brady: Thanks for having me, Bill.
Bill: What can you tell me about Powermaster?
Brady: Well, Powermaster Performance was started in 1981 making some OE parts. We do work for Richard Petty Driving School, Grave Digger monster trucks. In 1992, the Powermaster brand was started. What we do is high performance starters and alternators. We have a one-year warranty on our products and 90 days on some of the race stuff. We do a full refurb program for anybody that runs into a little trouble with an install or damages some products on a race vehicle.
We have everything from stock replacement alternators and starters all the way up to high performance gear reduction for engines up to 18 to one compression, alternators up to 200 and higher amperage. Basically anything for the street, strip and hot rod type applications.
Bill: Where are your products made at?
Brady: Everything we do is made in our 150,000-square foot plant in West Chicago, Illinois. We've been there since 1981 and we're not going anywhere.
Bill: I'm familiar with your starters and alternators, but I wasn't aware you guys made a generator.
Brady: Well, Bill, we actually don't. This is an alternator that just looks like a generator. This is for guys that are looking for a little bit higher amperage than the factory piece. We dyno test every starter and alternator that leaves the plant. Every alternator gets our proof of performance tag.
As you can see, this one did 90 amps at the top end, 72 at idle, which is well over three times the output a factory generator would've done. That's in half the weight of a factory generator package.
Bill: What can you tell me about this generator you brought with you?
Brady: What we brought with us today was the 200-amp in a natural finish here for upgrade on later model vehicles. We got a hundred amp one wire for a serpentine setup in a black finish. We also brought a chrome finish for the earlier models with the v-belt on it. That's again a one wire hundred amp hookup. Those come with the mounting hardware so that they'll bolt right into your Mustang. We offer anything from a stock replacement 60-amp externally regulated all the way up to that 200-amp of direct replacement.
Bill: They're all available in three finishes?
Brady: All available in not just these three finishes, but we also offer polished and a brand new satin finish that we're working on now.
Bill: Brady, I know starters are a big part of your business at Powermaster. Want can you tell us about this one you brought with you today?
Brady: This is our XS torque 200-foot pound starter. It's got a fully aluminum-encased solenoid and armature housing. What that does it helps keep heat soak down. The heat's going to dissipate right out of the starter motor during cranking. What it also has is our fully-adjustable intra-clock style feature. This starter can be rotated 360 degrees to clear headers and kick out an oil pan or really any obstacle you may have in the way, all in a package that will turn an engine up to 18 to one compression with no problems.
Bill: The Powermaster has taken a part that most people view as a replacement item and made it into a true performance necessity.
Brady: That's right. We've been making starters and alternators for your Mustang for over thirty years right here in the U.S.