Pair of Roush Black Textured Side Skirts/Splitters for all 2010, 2011, 2012, 2013 and 2014 Mustangs.
Add true race-inspired styling with this Pair of Roush Black Textured Side Skirts/Splitters (P/N: 420092) for your 2010-2014 Mustang. This kit includes side skirts/splitters for both the driver and passenger sides of your vehicle to create a much more aggressive styling line with the road!
Features and Benefits:
- Adds True Race-Inspired Styling
- Attaches to Bottom of Stock Rocker Panels
- Made from High-Strength TPO (Thermal Plastic Olefin)
- Black Textured OEM Finish
- Includes ALL Necessary Hardware
- Quick and Easy Installation
- Made in the USA
- Sold as a Pair
Constructed from high-strength TPO (thermal plastic olefin) for long lasting durability and made in the USA at Roush's own plastics manufacturing facility, the plastic is molded with high-pressure injection using the same process used by the automotive manufacturers. Installation will take only minutes and there is no trimming or permanent modifications necessary. These side skirts/splitters come unpainted and feature a black textured finish that will be more resistant to impact from rocks while driving. All required hardware and components are included.
*NOT compatible with aftermarket body kits.
How well do you want your Mustang to look and perform? With any of the parts from Roush Performance, you can give it a major performance overhaul, and add some visual styling that will make your Mustang stand apart from the crowd. CJ Pony Parts is a Roush Top 10 Dealer.
Order this pair of Roush's 420092 Black Textured Side Skirts/Splitters for your 2010, 2011, 2012, 2013 or 2014 Mustang from CJ Pony Parts today!
Product ReviewsWrite a review
Can I install this Roush Side Skirt/Splitter Kit on my 2011 GT500, and also wanted to ask you, if the Skirt/Splitter Kit comes with the two pieces for the rear bumper? Thanks
Does this fit for the basic 2013 v6?
what is the cost of full body without engine?
Does your kit include both side and rear splitters? The video shows a complete install but the description on reflects side. Can you please clarify. Roush sells the rear spliter separately.
You Might Also Like
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$268.99
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$249.99
/** * Cases for simple product that is not on sale */ ?>CJ's Low Price:$209.99
The rocker splitters are going to mount to your factory rocker moldings using these extensions and the Roush supplied push pins, as well as five additional holes we'll have to drill and tape to make sure your splitters don't go anywhere. The rear splitter is going to mount underneath the ends of your back bumper. They do require drilling for installation. Roush provides a template, as well as hardware and double stick tape to hold them on.
For this installation you'll need a jack and jack stands or lift, needle nose pliers, 1/4-inch ratchet, 7 mm socket, scissors, tape, drill, 1/8-inch pilot bit, 1/4-inch drill bit, rubbing alcohol, and safety glasses. Once you have your car off the ground your first step is going to be to remove the factory push pins holding on your factory rocker panel. You're not going to use them with the new pieces. The rocker will stay in place by the screws on the ends.
Now we're going to prepare our new rocker splitter for installation. The first thing you want to do is bend all these tape tabs over toward the edge. That way once you have it in place and held in place by the push pins you can slide that off and stick it to your rocker. Roush provides new push pins for installation. You don't want to push them in all the way yet. Leave about an eighth of an inch gap so you can remove the tape once it's in place.
When you line up the tabs, we're going to start with the one in the center and then move onto the two ends to hold it in place. Remember don't put them all the way in, leave a little bit of a gap. Now we're going to remove our tape. You want to make sure you slide the splitter as far back as you can on the studs before you pull the tape off. Now that we have it adhered to our rocker we're going to make all our push pins tight. It might be easier to use a screwdriver so you can get up there and put good force on the center.
Once you've installed all your pushpins in the factory locations, the Roush splitters have five additional holes that have to be drilled for additional support. We're going to put some tape about an inch down in your drill bit to use as a stop when you drill. Once you finish drilling your holes you can install your last five push pins.
Now that we're finished with our rocker splitter kit we're going to move on to the rear splitters. The rear splitters don't use any factory hardware, but require holes to be drilled in the bottom of our bumper cover. Roush supplies a template to tell you where to drill your holes.
You want to tape your template in place. It folds in front to follow the inside body line right here lining up with the factory hole in the back here. Once you have it in place, you can drill pilot holes in the center of each bulls-eye. Once you drill those, you can remove your template.
You want to save your template to use on the other side. Now we're going to open our holes up to the proper quarter inch diameter. Now we're going to install the supplied J-clip fasteners. Make sure the threaded stud is pointing up and slide her over the hole.
Now we're going to prep the splitter for installation. It comes with 3M tape. We're going to take the white backing off to prepare them to go onto the panel. Before we put them we're going to apply the supplied adhesion promoter. Just put it on the edge from the holes back. You don't want to put it all over the entire panel. Put the 3M tape on between the holes. In this case we are going to remove the tape first, then our panel is ready to install.
Now we're going to install the bolts to hold it in place. You don't want to tighten them all up yet, just enough to keep it hanging in place before you push up on the tape. Once you have them in place you push up on the panel, stick it into place with the adhesive, and then tighten down the bolts, and our installation is finished.
Now that we have our car back on the ground you can see how well our new rocker and rear spitter work with our previously installed Roush front splitter. It gives our lowered Mustang an even more aggressive look. The rocker splitters should take you no more than about an hour to install and figure about the same amount of time to do the rear splitters. You'll be back on the road in no time.