Scott Drake Exterior Door Handle Chrome Show Quality Kit 1965-1966

Scott Drake: C4DZ-6222404/5P
CJ's Low Price:
$70.99
In Stock
Free Same Day Shipping
Orders placed by 5:00PM Eastern time ship today1406246400
Earn 70 RPM Points What's this?
EDH13
EDH13 EDH13_1 EDH13_2 EDH13_3 EDH13_4 EDH13_5 EDH13_6 EDH13_A Play Scott Drake Exterior Door Handle Chrome Show Quality Kit 1965-1966 Video 1 Play Scott Drake Exterior Door Handle Chrome Show Quality Kit 1965-1966 Video 3

Product Description

Scott Drake Show Quality Chrome Exterior Door Handle Kit for 1965-1966 Mustangs.

Get your exterior door handles looking and working like new, with this show quality chrome plated door handle kit from Scott Drake. This kit now includes pivot mechanisms and rod clips. Scott Drake door handles are the absolute best on the market.

Made in the U.S.A.

Includes:
-Driver & passenger handles
-Buttons
-Pivot mechanisms
-Rod clips
-Gaskets
-Hardware

OTHER APPLICATIONS
1966-1977 Ford Broncos
1964-1965 Mercury Comets
1964-1965 Ford Falcons

Similar Mustang Parts

similar mustang parts More Mustang Exterior Door Handles  

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a Review
good chrome
put on my 65 fastback, they have been ion for a couple of years now and look new, i used some old parts and mixed it with these
RAH April 12, 2014
Poor chrome quality
I bought several parts from scott drake to restore my 66 mustang coupe. A year passed since I installed the new door handle kit and my car never left the garage because of its restoration. The door handles are slightly pitted while other parts installed the time look like I installed them the first day. I think these scott drake parts are made in taiwan that should explain the poor chrome quality. I'm very disappointed about Scott drake this time.
Max March 9, 2014
Door Handles
These look great, but you will need to use the original hinge piece on the inside of the door. The one that comes with the kit does not work. Do this and it will work fine.
kdx99 November 2, 2012
door handles
This product fit like an original part. I was very satisfied with the way it fit and looked. I would recommend this to anyone.
Richard Neal March 8, 2012
nice door handles
nice door handles work fine just use the original piece that the button slides through inside the door the one that comes with it gets stuck sometimes
Eamon Bakos March 8, 2012
5 Results

Product Video

By Bill Tumas: With all the chrome on the outside of your classic Mustang, the exterior door handles are probably the ones that take the most abuse. Between the wear and tear of being on the outside of the car, plus the use they get every time you open the door, faded, pitted door handles are pretty common.

Today we're going to replace the door handles on this '67 Mustang convertible using these show quality replacements from Scott Drake. The kit includes both left and right side USA-made door handles, new gaskets, internal hinges, as well as springs and hardware. For this installation you'll need a door panel removal tool, Phillips head screw driver, quarter inch ratchet, 3/8" deep socket, 3/8" shallow socket, pliers, flashlight, and a small screw driver or pick.

As you can see our existing door handles are in pretty bad shape. Pitting and wear, it's very typical of the exterior door handles. To remove them, there's a screw over here and there's another one on the inside that we'll have to take the door panel off to get to. We'll start with the screw. To get to the inside nut, the door panel is going to have to come off. We're going to start with the window crank and the door handle. Both of them are held in place by one Phillips head screw.

Now we're going to remove our armrests. Two bolts at the bottom of the arm rest hold it to the door. Next we need to remove the bezel for our remote mirror; these just simply thread in place and usually are pretty tight. If you can't get it off by hand, grab a set of pliers; just put something over to make sure you don't damage the chrome. The last step in removing the door panel is to remove all the clips around the outside edge. We're going to carefully peel back the water shield. We're going to roll our window up so it's out of the way and you can reach the door handle nut. The nut should be a 3/8". You want to get a swivel if you have it, or some sort of a ratcheting wrench would help as well. You're going to go up through here, underneath the regulator up to get the nut off. You want to make sure the window is as high as possible so you can fit your arm in easily.

The stud is most likely going to come out with the nut, which is okay. You want to make sure you're holding onto the handle. On a freshly painted car, it's not a bad idea to put some painters tape around it, because the handle will be loose now. Once you have the hardware removed, you need to remove the rod that goes from the door handle to the door latch itself and its going to be at the bottom of the door. There's a little metal clip; once you pull the clip off, pull up the handle at an angle, and pull the whole assembly out of the door. Now we need to remove the rod from the factory handle. There's a little metal clip here. As you push up on the clip and the rod will slide out.

Now we can assemble our new door handle. We'll start by taking the O-ring and putting it over the button; just roll it down to the bottom. We'll put the button into the handle. Put it through from the inside, and then place the spring over the back of the button. Now you want to put your exterior gasket on first and then the latch can go on. This black grommet is going to go over the back of the button, push it down into place and use the provided screw to hold it in. Make sure the buttons and the springs are seated properly. Now we are going to reinstall the door latch rod. Make sure it goes on the inside hole, not the outside. Install the new supplied clip, press the rod through, lock the clip into place.

The last step before reinstalling the handle is to put the threaded rod on the outside and pull through. We're ready to reinstall our handle; I want to make sure we have both gaskets seated properly on the handle. We are going to fish the lock rod down; we're just going to get the handle in place. We're going to install the outside screws to hold the handle in place so we can reconnect the door latch rod. Now we can connect the rod to our latch itself, connection is the same way on top, the bar is going to slide in and have a little metal clip to go over it, you can see it from the side, the best way though is to put your arm in and just go by feel.

Now our last step inside the door is to put the new nut on the stud for the handle. You want to make sure the gaskets line up on the outside and we're going to tighten the screw down. Our last step before we put the door panel back together, make sure our handle is working properly, you can close the latch with your finger, push the button, working properly. We'll double check the lock just to make sure nothing got disconnected, close it again, lock it, everything is working properly. Now we know our new Scott Drake chrome door handles look great, they're functional as well. The most time consuming part of the installation is going to be the door latch rods, figure on about an hour per door and you'll be back on the road in no time.