Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013

CJ's Part Number: MSK312-V
MSRP: $79.99
CJ's Low Price:
$69.99
1480636800 57760
Add this great retainer to properly install your new shift knob.
Earn 69 RPM Points What's this?
Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013
Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Play Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Video 1
CJ Shift Knobs

Product Description

Rally III 2-1/8" Shift Knob with a 6-Speed Shift Pattern and Boss 302 Logo for all 2012-2013 Boss 302 Mustangs with a Manual Transmission.

If you’re looking to switch up the dull, stock shift knob in your 2012-2013 Boss 302 Mustang, then add the perfect touch of color to your interior with this new rally III 2-1/8” shift knob featuring a 6-speed shift pattern and Boss 302 logo from CJ Pony Parts! These race-inspired shift knobs are designed with eye-catching colors and rally III style stripes in a high gloss finish that give your Mustang’s interior the classic, yet custom look that all enthusiasts are after.

Features and Benefits:
- Available in a Variety of Colors
- Correct 6-Speed Shift Pattern (Reverse to the Left and Up)
- Inlaid Rally III Style Stripes
- Etched Boss 302 Logo
- Made Using High Quality Partek Resins
- Engineered for Strength and Durability
- 2-1/8” Diameter and 12mm x 1.25 Thread Pattern
- Manufactured in the USA

What are rally III style stripes? Rally III stripes consist of three separate stripes; two small outer stripes surrounding a wide inner stripe. These stripes run horizontally on the driver and passenger side of the shift knob to simulate rocker stripes. The Boss 302 logo is located on the back of the shift knob, facing the rear of the car once properly aligned.

These American-made manual shift knobs are manufactured using the same high-quality partek resins found in world class billiard balls, and are engineered for long-term strength and durability. Choose from a variety of stripe and color combinations that suit your individual taste. Color options are listed by knob color, then stripe and logo color. The shift pattern and Boss 302 logo are both the same color as the stripes and are inlaid, polished smooth to the touch.

This custom shift knob features a 2-1/8" diameter and the correct 12mm x 1.25 thread pattern for your 2012-2013 Boss 302 Mustang.

*All knobs are custom made to order and take 3-4 weeks to ship from CJ Pony Parts.

Please Note: This manual shift knob does not include a jam nut. However, a jam nut or threaded shift boot retainer is required to make sure the shift knob is properly aligned when tightened on the shift handle. A shift boot retainer is recommended instead of a jam nut as it will prevent a gap between the new shift knob and the factory boot. Without a jam nut or shift boot retainer you run the risk of splitting the shift knob in half if you over tighten knob when it bottoms out on the shift handle.

Order a Rally III 2-1/8" Shift Knob with a 6-Speed Shift Pattern and Boss 302 Logo for all 2012-2013 Boss 302 Mustangs with a Manual Transmission from CJ Pony Parts today!

Similar Mustang Parts

similar Mustang parts More Shifter Knobs  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 99.37ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 179.8ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 403 was returned;

You Might Also Like

Product Video

Shift Knob 2-1/8" Rally III With Shift Pattern And Boss 302 Logo 6-Speed Boss 302 2012-2013 Video Transcript
By Bill Tumas: If you're looking for any easy upgrade for the interior of your Mustang, you can't go wrong with an aftermarket shift knob. Here at CJ's we have a huge selection, including these 2 1/8" diameter USA made knobs, available in 13 colors. With or without stripes, with your choice of graphic, there's over a thousand different options available.

You should have no trouble finding one that looks great in your Mustang.

Installation for the shift knob is very easy. If you're early Mustang you'll have to thread on this jam nut. If you're '05 and up, we carry these retainers that will hold your boot in place once you install the after market knob.

All the knobs are available in solid colors, without any graphics whatsoever. If you chose to go with a graphic, we offer the 5.0, the running horse, the snake, the GT, as well as a Boss 302. If you choose to go with a pattern, stripes are available as well. And if you prefer, you can actually have the graphic added to the side.

In our case, we had this custom one made for our CJ race car with our CJ emblem on the side. We'll be installing this one.

Since quarter mile performance has been the goal with our gotta have it race 2013 GT, we're still running the stock shift knob. We'll remove this one and install our new green knob. Get a good grip on the knob and turn it counter clockwise.

First step for the installation of the new knob is to install its retainer. The retainer's gonna hold the boot in place and also work as a jam nut for the knob. Thread your retainer down until it's touching your shift boot. Grab your shift knob, line up the threads. Start threading it on. Now, if you thread it all the way down, it probably isn't gonna line up straight.

What you'll wanna do then is loosen it up until it's about an eighth of a turn from straight, thread the retainer upward. Get a good grip on it, turn it until it's straight. As you can see our shift knob was a nice additional upgrade to our interior. It only took a few minutes to install. You'll be back on the road in no time.