Powermaster Chrome XS Torque Mini Starter for 164 Tooth Flywheel Equipped 1969, 1970, 1971, 1972 and 1973 Mustangs with a 302 or 351W Engine and a 3 or 4-Speed Transmission.
Does your 1969, 1970, 1971, 1972 or 1973 Mustang not want to start due to a bad starter? Replace your damaged or worn out factory starter with this high Performance starter from Powermaster. This XS Torque Mini starter features a 3/4" offset for proper mounting alignment. Offset is the distance from the mounting surface of the starter to the engine side of the ring gear.
Powermaster's highly efficient XS Torque starters feature extra-powerful motors that churn out up to 200 ft.-lbs. of torque. Coupled with their 4.4:1 gear-reduction ratio, that adds up to reliable cranking power for engines up to a whopping 18.0:1 compression ratio. These starters come with a billet adapter/mounting block and will clear all headers. They'll also clear your oil pan if the OE starter did. Starter dyno test results are included.
- Chrome Housing
- 4.4:1 Gear Reduction
- Recommended for 18:1 Compression
- Machined Aluminum Adapter Block
- Adds extra Clearance
- Weighs 8.5 lbs.
Please Note: This Powermaster starter is designed for a 164 Tooth Flywheel.
*Small block engines refers to 302 / 351W.
Powermaster Performance offers high performance Starters for early model Ford Mustangs. Powermaster has a wide range of choices to fit just about any application. Check out CJ Pony Parts large selection of starters from Powermaster and get your Mustang back on the road in no time.
Order your new Powermaster Chrome XS Torque Mini Starter for 164 Tooth Flywheel Equipped 1969, 1970, 1971, 1972 and 1973 Mustangs with a 302 or 351W Engine and a 3 or 4-Speed Transmission from CJ Pony Parts today!
Product ReviewsWrite a review
You Might Also Like
Regular Price: $267.99
Special Price: $241.19
Regular Price: $246.99
Special Price: $222.29
Regular Price: $236.99
Special Price: $213.77
Regular Price: $230.99
Special Price: $207.89
Regular Price: $178.99
Special Price: $161.09
Power Master is serious about the performance of the XS torque starters, so much so that every one of their starters comes with one of these dyno sheets showing you actual performance the starter put out. They also use the smallest chassis possible and their Infi-clock system allows turning in the mounting bracket, making it much easier to install in your Mustang.
The XS torque starter's going to come with two terminals mounted on it. If you're installing one of these in your early Mustang like we are, you'll want a jumper between these two since you're using a single wire with an external starter solanoid for your classic Mustang.
For this installation you'll need a jack and jack stands or lift, 3/8th ratchet, 12-inch extension, 9/16th socket, 1/4-inch ratchet, 9/32nd socket, crimping tool, wire strippers and safety glasses. The bottom bolt is pretty easy to get to; the top one we're going to have to use an extension or a swivel of some sort. The header is going to make it a little bit harder; you should be able to get it off though.
You've got to remove the wire. Since our early Mustang has an external starter solanoid, you'll want to make a jumper to go between the two terminals on the starter. You connect the starter to the starter wire before you put it up in to place. You'll want to get this connection snug; you don't want to overtighten it. Now I can put our starter up in to place.
Once our starter is bolted and the wires are connected, we're ready to test it! Our Power Master starter had no problems with our stock 289 and is strong enough for any motor we put in, in the future. Installation, figure 45 minutes to an hour. You'll be back on the road in no time.