Total Control Products Bump Steer Kit Manual Steering 1965-1966

Total Control Products: TCP TIER-08
CJ's Low Price:
$199.99
1480723200 50661
Earn 199 RPM Points What's this?
Total Control Products Bump Steer Kit Manual Steering 1965-1966
Total Control Products Bump Steer Kit Manual Steering 1965-1966 Play Total Control Products Bump Steer Kit Manual Steering 1965-1966 Video 1
Total Control Products

Product Description

Total Control Products Bump Steer Kit for all 1965-1966 Mustangs with Manual Steering.

Dial-in your 1965-1966 Mustang's manual steering setup with this all-new bump steer kit from Total Control Products. The Total Control Products bump steer kit can minimize and in some cases practically eliminate the bump steer affect in your 1965-1966 Mustang, making handling more consistent and predictable.

TCP Bump Steer Kit Includes:
- Adjustable outer tie rod ends
- Shim spacers
- Billet-steel adjuster sleeves

Most evident on rough road surfaces, during hard cornering or under heavy braking, bump steer is the change in toe, or left to right angle, as the suspension moves through its range of motion. Toe is measured by the difference in the track width of the leading edge and trailing edge of a set of tires. Up to 3/8 inch of toe change can be experienced when your suspension is moving through its full range of motion and can cause erratic, uncontrolled steering. Excessive bump steer increases tire wear and makes the vehicle dangerous and more difficult to handle on rough roads.

Please Note: This bump steer kit requires the use of V8 spindles and inner tie rods, and 11/16-18 (.688) thread on adjuster sleeve shaft. This bump steer kit will not fit the 3/4-18 factory power steering inner tie rods.

Order a Total Control Products Bump Steer Kit for your 1965-1966 Mustang with Manual Steering from CJ Pony Parts, and reclaim the absolute steering control you were meant to have!

Similar Mustang Parts

similar Mustang parts More Restomod Suspension  

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Ford Mustang years:

Product Reviews

Write a review
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 164.88ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Product Questions

Is there a bumpsteer kit for a 1966 mustang inline 6? 

Asked by: Austin v
This will work with all 1965-1966 Mustangs with Manual Steering.
Answered by: CJPP Dave
Date published: 2016-09-01

Will this work with the Borgeson power steering conversion set up?

Asked by: Vinburg
  • 2016-12-03T08:03CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_TCPTIER08, PRD, sort_recentAnswersFirst
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 241.35ms
  • QUESTIONS, PRODUCT

You Might Also Like

Product Video

Total Control Products Bump Steer Kit Manual Steering 1965-1966 Video Transcript
By Bill Tumas: We’re here with a Bump Steer Kit from Total Control Products fitting your 1965-1966 Mustang with manual steering. This Bump Steer Kit is going to replace the outer tie rod ends on your 1965-1966 Mustang with manual steering and correct the bump steer issue common in Mustangs; especially when they're lowered. Bump Steer occurs to the changes in toe with suspension movement. The more erratic these changes get, the worse your steering can get causing very erratic and dangerous steering. This bolt-on kit will correct that issue and will require alignment when finished. Due to the differences in outer tie-rod ends, this kit will only fit a manual steering Mustang. It will not work with power steering.