aFe Cold Air Intake System Momentum GT With Pro Dry S Filter F-150 Raptor 2017-2018

aFe:
51-73115

Highlights

  • Roto-Molded Intake Tube
  • One-Piece Sealed Housing
  • One-Piece Sealed Housing
  • Pro Dry S 3-Layer Filter
MSRP $550.00
$445.00
You save 19%

aFe Stage 2 Momentum GT Cold Air Intake System with a Pro Dry S Filter for 2017-2018 F-150 Raptors.

Increase the amount of cold air being pulled into your new 2017-2018 F-150 Raptor engine while maintaining an easily inspected filter with this aFe 51-73115 Stage 2 Momentum GT Cold Air Intake System. Adding aggressive style, this cold air intake system is designed to achieve maximum power gains while maintaining a perfect fit under your Raptor's hood.

The smooth one-piece sealed housing is used to eliminate the use of multiple-piece housings and ensure the coolest air intake charge available. A large, clear sight window is used for a hassle-free filter inspection and an aggressive style. This System uses a CAD designed, dyno-tuned, roto-mold intake tube to achieve maximum power gains while maintaining a perfect fit.

The Momentum GT intake is designed around an oil-free, large 9-inch tall conical inverted top 360 degree radial flow performance air filter with 3-layers of progressive finer porosity synthetic media providing maximum convenience. The unique air filter-to-housing interface allows for maximum filter size which increases the available air volume while simplifying the installation process.

Premium stainless steel T-bolt clamp and silicone couplers are used for strength and durability while also providing the most secure installation available. Momentum GT intakes are designed with fewer parts for a quick and simple installation that does not require modifications to your 2017-2018 F-150 Raptor.

Cold Air Kit Features and Benefits:
- CAD-designed roto-molded intake tube
- One-piece sealed housing
- Built-in sight window provides easy inspection of filter without disassembly
- Unique filter-to-housing interface for easy installation
- Pro Dry S oil-free 3-layer progressively finer porosity synthetic media for maximum convenience
- No cutting or drilling on factory parts for faster installation

Please Note: This intake system is not CARB exempt at this time and is not for use in California or on vehicles registered with the California Department of Motor Vehicles.

Order this aFe 51-73115 Stage 2 Momentum GT Cold Air Intake System with a Pro Dry S Filter for your 2017-2018 F-150 Raptor today from CJ Pony Parts.

California Residents: Proposition 65 Warning

Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.

Installation Videos

Video Transcript

Factory intakes are just not okay here at CJs, so today we're going to further improve the performance of our 2017 Raptor by installing this aFe Momentum GT Cold Air Intake with a Pro Dry S Filter. This aFe cold air intake is going to directly replace the factory intake and inlet, in order to outflow for better performance and sound. It features a Roto-Molded intake tube with a one piece housing for maximum airflow, and a Pro Dry S Filter that's washable and reusable. It simply installs with all the necessary hardware included, so today we're going to install it on our 2017 Raptor. Tools you'll need for this installation, a 7mm socket, 8mm socket, 11mm socket, 13mm socket, an extension, 1/4" ratchet, 3/8 ratchet, a trim panel removal tool, or a flathead screwdriver, and you might need a set of pliers.

All right, this intake is actually really straight forward to install. The first thing we're going to do is remove the factory Y pipe and air filter housing. Remove this clamp on the Y pipe that connects it to the passenger side inlet tube. Next you're going to want to remove this clamp right here. It's hard to see, but the screw for it is back behind here in the backside of the tube. Remove these two clips, pull out on the air box, remove it from the inlet tubes. Disconnect this colon hose. From the backside, there's a temperature sensor that you have to remove, press on the tab, and pull it off. Get rid of this extremely restrictive air filter, remove the two clips securing the air inlet. Pop the two yellow tabs off the factory air box and this clip right here. Finally, remove this bolt right here with a 13mm wrench. The whole air box can now come out.

With the factory system out of the way, the first thing we're going to install is this vent tube insert. This will prevent you from getting a check engine light because the intake flows so much more. Locate the PCV hose that goes to the driver side turbo inlet pipe and pop it off. We're going to insert this tube with the open portion facing the turbocharger, so it's going to go in just like this in the tube, not like that. To install it like this, it won't do anything, it needs to be installed like this. Press it in all the way, then reinstall the hose.

This grommet on the factory air box needs to be removed and transferred over to the aFe air box. Pop it out. Install it into the aFe air box. Don't forget the metal sleeve. Install your new aFe air box. It's kind of difficult to see, but the first thing we're going to do now that the air box is installed is reinstall the bolt into the grommet that you just installed into the aFe air box. Reinstall the factory clips up front. Reinstall this gray clip on the air box. Install this weather stripping around the edge of the air inlet. Now this will seal it nicely against the hood. Reinstall this gray clip.

Before we install the aFe Y-pipe, we need to transfer over the temperature sensor from the factory pipe. Carefully grab it with a set of pliers and twist it to remove it. Be very careful with these, they are easy to break, so be very gentle with them. Install the provided grommet into the aFe Y-pipe. Insert the metal tube, then you can install the temperature sensor. Place the air filter inside of the air box. Make sure it's seated well. Place a clamp over the smaller coupler and place the smaller end on the passenger's side turbo inlet plate. Place the larger coupler on the driver's side inlet plate. Place the other larger clamp on the coupler that you just installed and your leftover clamp, which should be the middle sized one, will go right here on the passenger's side inlet. Everything's in place, the Y-pipe can now be installed. Okay, everything is now assembled, we can tighten all five clamps. Connect the temperature sensor plug and your installation's finished.

All right, our aFe cold air intake is installed. It looks way better than the factory intake and it's going to help our Raptor breathe a lot better too. Installation's super easy. It should take you less than an hour and before you know it, you'll be heading off-road.

Vehicle Fitment

This product will fit the following F-150 years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.