American Car Craft Air Conditioning Vent Trim 6-Piece Kit With Etched Pony Logo Brushed Stainless Steel Performance Package Mustang 2015-2022
Highlights
- Stainless Steel Construction
- Will Not Tarnish, Fade Or Rust
- Etched Running Pony Logo
- Made In The USA!
American Car Craft Brushed Stainless Steel 6-Piece Air Conditioning Vent Trim Kit with Etched Pony Logo for 2015, 2016, 2017, 2018, 2019, 2020, 2021 and 2022 Mustangs Equipped with the Performance Package.
Are you looking to add a custom touch to the interior of your 2015-2022 Performance Package Mustang? Well, take a look at this 271053 Brushed Stainless Steel 6-Piece Air Conditioning Vent Trim Kit with Etched Pony Logo from American Car Craft!
Features and Benefits:
- Official Ford Licensed Product
- Stainless Steel Construction
- Covers 2 A/C Vents
- Etched Running Pony Logo
- Brushed Satin Finish
- Will Not Tarnish, Fade or Rust
- Peel and Stick Installation
- Made in the USA
Constructed from high-quality stainless steel, this air conditioning vent trim kit is officially licensed by Ford. These American Car Craft trim pieces come in a satin brushed finish that will not tarnish, fade or rust and feature an etched running pony logo for a nice custom touch. Made right here in the USA, this trim kit will cover the 2 A/C vents on the center dash of Mustangs with the Performance Package, and uses a simple peel and stick application that only takes minutes to install.
Please Note: This 6-piece vent trim kit is designed specifically for Mustangs equipped with the performance package.
Vehicle Fitment:
- 2015-2022 Mustang with Performance Pack
California Residents: Proposition 65 Warning
Related Categories: Mustang Parts, Mustang Air Conditioning & Heating, Mustang Heater Registers, Mustang Interior, Mustang Interior Trim Kits


Installation Difficulty

Novice skill is required for this installation.
Installation Videos
Video Transcript
These AC vent covers are going to fit all 2015 through 2017 Mustangs with the performance pack option. This is a six-piece kit made of stainless steel with embossed running horse, and it's easy to install with supplied double stick tape and primer.
To begin the installation first I clean the vents off, use some rubbing alcohol, just get the surface as clean as possible so our tape will stick. What you want to do now is, the stainless steel is flexible because it is thin, and this does have a slight curve to it. So what you want to do is sort of lay it where it's going to go, sort of bend it a little bit into place. Sometimes you may want to pull it off, just push it a little bit. You want to get it as flat as possible on the plastic once it's installed. We do the same thing with all the pieces. Now I grab the supplied adhesion promoter, put that all over everything.
And remove the red backing from the double-stick tape. Line it up, and press it on. Now do the same thing with all the other pieces. And then do the same thing with the bottom piece. Then repeat the process with the other vent. They curve the panel, you want to have a nice smooth curve. You can actually use the side console and just lightly press down just to get a slight curve. Make sure it lines up.
Once you have them installed, make sure everything works like it should, make sure you have no clearance problems, and your installation's finished.
The polish round with the brush set on the American car craft vents can make it almost a factory option. It really blends well with the interior. Again, this is for performance pack only because we had the gauges in the middle. They also are available for their non-performance pack to be a three-piece kit there. First installation, you just want to take your time doing it, but again, this is a fifteen, twenty-minute installation. You'll be back on the road in no time.