Borgeson Power Steering Pump Saginaw Kit 289/302/351W 1965-1970

Borgeson:
800330
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 149.15ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Highlights

  • Includes Mounting Hardware
  • Easy Installation
  • Upgraded Power Steering Pump
  • Uses Stock Ford Hoses
MSRP $363.98
$265.50
You save 27%

Borgeson Saginaw Power Steering Pump Kit for 1965, 1966, 1967, 1968, 1969 and 1970 Mustangs with a 289, 302 or 351W V8 Engine.

This is a worthwhile upgrade to consider when upgrading your existing power steering to a Borgeson Saginaw Power Steering Pump Kit. Provides better power assist at idle and enhances response and drivability over the Ford pump.

Kit Includes:
- Saginaw Power Steering Pump
- Saginaw Power Steering Pump Bracket
- Power Steering Pump Pulley
- All Necessary Mounting Hardware

Please Note: If using the stock Ford hoses, you will need a hose adapter, part number HW3409.

You will be able to easily replace your broken, old and tired OE power steering pump with this new Borgeson Saginaw Power Steering Pump Kit. Coming with everything you need, this kit will make the restoration process on your 1965-1970 Mustang a breeze. Installation is simple and straightforward coming with all necessary mounting hardware.

The steering on your classic or late model Mustang contains many vital components for keeping your Mustang on the road. If one of these components should break, or you want to perform an upgrade to add some higher quality insurance for the future, the steering components from Borgeson should be at the top of your list.

Order a Borgeson Saginaw Power Steering Pump Kit for 1965, 1966, 1967, 1968, 1969 and 1970 Mustangs with a 289, 302 or 351W V8 Engine from CJ Pony Parts today!

Installation Difficulty

Moderate
Moderate

Intermediate skill is required for this installation.

Vehicle Fitment

This product will fit the following Mustang years:

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 8.06ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

When installing power steering pump 800330 in a 67 mustang the instruction state that cars with AC will use only the two long spacers, is an aftermarket AC the same as the original ac cars as far as pulley alignment is concerned?

Asked by: hamfissted
Most aftermarket AC brackets are the same thickness as the original and pulley alignment should be fine.
Answered by: Borgeson
Date published: 2018-09-13

Have a 67 mustang 289ci will this kit work with air conditioning pump above it 

Asked by: Harpoon
Access to the power steering fill cap can be limited with the factory AC compressor but the pump kit will fit under it.
Answered by: Borgeson
Date published: 2018-09-07

What is the pump pressure and flow rate? I have a Mustang II power rack and pinion steering. The recommended pump pressure is 1000psi and the flow rate is 2gpm.

Asked by: wa_poni
This pump will have too high of a pressure as it ships this pump is around 1250 PSI, we do offer a pressure reducing kit #899001 that will allow you to adjust the bypass pressure down to the range you need.
Answered by: Borgeson
Date published: 2018-08-20

I purchased the steering upgrade kit from Borgeson, including steering box ,column rod, hoses ect. I was going to use the stock pump. It leaks. Will these new hoses work with the saginaw style pump?

Asked by: numbnuts
You would need these hoses for use with the Saginaw pump. https://www.cjponyparts.com/borgeson-power-steering-hose-gm-pump-set-289-302-351w-1965-1970/p/PSHK4/
Answered by: rk cjpp
Date published: 2018-07-25

I am replacing the factory power steering control valve with CJ Pony Part CV4 and factory power steering pump with Borgenson pump #800330. Do I need special pressure and return hoses for this setup. Thanks

Asked by: lundy
You should only need this adapter. https://www.cjponyparts.com/borgeson-power-steering-hose-adapter-fitting-saginaw-pump-to-ford-hose-1965-1973/p/HW3409/
Answered by: rk cjpp
Date published: 2018-05-21

will this fit on 1970 mustang with a 351 cleveland engine

Asked by: fastdom351
The vendor has not provided any information regarding cross-fitments of this part to any other model then what is listed.
Answered by: rk cjpp
Date published: 2018-04-24

I have a 1969 mustang, 351 Windsor, with vintage air conditioning. The stock pump uses a bracket from Vintage Air. Can I mount this pump in its place?

Asked by: KWBA
Yes there are extra spacers in the kit that allows you to mount this on a/c equipped vehicles.
Answered by: rk cjpp
Date published: 2018-04-09

What all do I need to change? Have 302 68 mustang coup manual steering.

Asked by: Mitty
Provided you Mustang has an automatic transmission our kit #999021 will include all items needed. The only other item you will need to make sure you have other than this kit is at least 2 rows on your crank pulley.
Answered by: Borgeson
Date published: 2018-02-22

Hi, Will this fit on a standard 289 with original Ford power steering ? And do i need additional fitting and pulleys?

Asked by: ats123DK
You can use this with the ford power steering, you will need this fitting, https://www.cjponyparts.com/borgeson-power-steering-hose-adapter-fitting-saginaw-pump-to-ford-hose-1965-1973/p/HW3409/
Answered by: rk cjpp
Date published: 2018-01-30

I have a 1966 mustang with a 347 stroker will this pump work for it?

Asked by: Ryan 1966 Flames
It should.
Answered by: rk cjpp
Date published: 2017-11-20

I want to replace my original 1965 ford Power Steering pump with this Borgeson pump...will I need to change all the hoses... are the couplings on the high/low presser lines the same?

Asked by: Charlie48
You would need this fitting, https://www.cjponyparts.com/borgeson-power-steering-hose-adapter-fitting-saginaw-pump-to-ford-hose-1965-1973/p/HW3409/
Answered by: rk cjpp
Date published: 2017-11-10

it seems like the pump and fluid get very hot , hoses are mounted up and away from the headers but the pump gets so hot you can't put your hand on it and it doesn't take long to heat up even with the car just setting. what is a good temp. what is to hot ?

Asked by: bobste
Power steering temps can run as hot as 180-200 degrees. We usually like to see it below 180, if your temps are getting higher than that you may consider adding a power steering cooler as it adds fluid volume and cools the fluid before be pressurized again.
Answered by: Borgeson
Date published: 2017-11-07

I had just installed Power steering Control Valve that I just bought from CJ Pony.   I was hoping it would help with the looseness of the steering and stop the ' whining noise ' that occurs at slow speed or idle.  Does this Borgeson Power pump help.     

Asked by: Mustangmonty
The Borgeson pump will help with the whining noise but will not eliminate and looseness in the steering system.
Answered by: Borgeson
Date published: 2017-09-05

Will the kit fit and work with the factory original A/C compressor on a 1967 mustang? will the brackets interfere?

Asked by: Boss302
It comes with different length spacers to work with a/c.
Answered by: rk cjpp
Date published: 2017-08-31

I have a 67 cougar and put the Borgeson box with the Ford pump and would like to up grade to this pump. Will it work with the original A/C system that came with my car. Thanks

Asked by: coolcougar
Yes, it includes different size spacers to work with a/c, you will also need to change the hoses, http://www.cjponyparts.com/borgeson-power-steering-pump-saginaw-kit-289-302-351w-1965-1970/p/PSHK4/
Answered by: rk cjpp
Date published: 2017-08-29

I have a 1969 mustang 351W, I changed to the Borgeson power steering but used the stock pump. The hose is located very close to the headers & the fluid gets very hot & damaged the pump. I want to change to the Borgeson pump what will I need

Asked by: gary 1969
You will need our pump kit #800330 and hose fitting adapter #925123 to change over.
Answered by: Borgeson
Date published: 2017-08-09

I've got a 1980 302 sbf in my f100. No AC. Hydroboost and powersteering running a 6rib pulley. Will this kit fit this engine? Is a 6rib pulley available to replace the single vbelt?

Asked by: Kevin62F100
No this will not work for your application.
Answered by: rk cjpp
Date published: 2017-07-24

Wondering if this pump will work in a '68 with a 390 also?

Asked by: Ethan68
No it will not.
Answered by: rk cjpp
Date published: 2017-06-20

I am building a 66 mustang originally a v8 car. I am putting in a 302 out of a 77 granada. Will one of these ps conversions work on my setup.

Asked by: Santaclause1
The 800330 power steering pump kit will fit a 1977 Ford 302
Answered by: Borgeson
Date published: 2017-05-01

I want to get this for my '65 Mustang, 289 engine. I have a 2 groove main pulley. The first pulley (closest to the engine) is for the alternator and fan. The second pulley (farthest forward) is for power steering. Does this line up with that pulley?

Asked by: TGoatman
This will line up with your second pulley on the crank. (farthest forward)
Answered by: Borgeson
Date published: 2018-09-13

Will this pump work with my stock power steering control valve and slave cylinder on my 289 65 mustang

Asked by: Draztik
You will need our pressure reducing kit #899001 to tune the pressure for the factory system and our part #925123 hose fitting adapter for adapting the factory hoses.
Answered by: Borgeson
Date published: 2017-04-12

how much is postage to australia for the borgeson power steering pump 1968 mustang 302

Asked by: speecho
To get a shipping quote and total price, add the item(s) to your shopping cart and then proceed to checkout. In checkout, fill out your address info and scroll down to see shipping options and costs to your area including any import taxes and duties.
Answered by: rk cjpp
Date published: 2017-02-28

What type of fluid does the Borgeson Power Steering Conversion kit use, power steering fluid or transmission fluid. I have seen references to both in some publications.

Asked by: Shadowman
If you are using our kits that include the power steering pump use GM power steering fluid. If you are retaining a stock Ford pump use the specified transmission fluid for your original application.
Answered by: Borgeson
Date published: 2017-02-10

I am thinking of replacing my stock power steering pump on my 1965 Mustang (289 V8). I am wondering if this Pump is compatible with my stock steering box and hoses. Will I need to replace them?

Asked by: RonW
The pump kit will fit. You will need fitting adapter #925123 to adapt your existing hoses. The pump is set for optimal pressure to work with our power steering conversion box however you can adjust the output pressure with our pressure reducing kit #899001 to best suit the factory system.
Answered by: Borgeson
Date published: 2017-01-20

I Have a 1964.5 With a 289 and Without A/C, and it has the Factory Power Steering, Will This Power Steering Pump Saginaw Kit Work/Fit in My Vehicle??.....

Asked by: MADS65STANG
The pump kit will fit. You will need fitting adapter #925123 to adapt your existing hoses. The pump is set for optimal pressure to work with our power steering conversion box however you can adjust the output pressure with our pressure reducing kit #899001 to best suit the factory system.
Answered by: Borgeson
Date published: 2017-03-27

Since the pressure for a Ford rack is much less than a GM pump, is this pump safe to use on my Ford?

Asked by: ScottE
This will only work on the factory style power steering systems found on 65-70 mustangs.
Answered by: rk cjpp
Date published: 2017-01-09

I need a pump kit for my 302 Ford with a short water pump, 4.5 inch from base to end of shaft, will this kit work?

Asked by: ScottE
No it will not.
Answered by: rk cjpp
Date published: 2017-01-05

What psi pump pressure and gpm?

Asked by: Mrstephs
The manufacturer has not provided that information.
Answered by: rk cjpp
Date published: 2016-08-23

Will the pump fit a 1966 289 stock A/C car? (clearance to the stock AC compressor)

Asked by: Matt_SWE
The kit comes with different size spacers to fit a/c and non a/c cars.
Answered by: rk cjpp
Date published: 2016-06-22

 Can you use the same belt or does it need a longer or shorter one?

Asked by: Stonebuster
For my 68 with a 302  I did need a longer belt. I went and got a belt that is 50 5/8"  and it seems to be the right size 
Answered by: Stonebuster
Date published: 2018-09-13
  • y_2020, m_1, d_17, h_13CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.4
  • cp_2, bvpage2n
  • co_hasquestionsanswers, tq_55
  • loc_en_US, sid_PSPK2, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 223.56ms
  • QUESTIONS, PRODUCT