Borla Axle-Back Exhaust System 2-1/2" Atak Dual Exit With 3-1/2" Polished Tips Jeep Wrangler JK 2012-2018

Borla:
11860

Highlights

  • Aggressive Exhaust Tone
  • Stainless Steel Construction
  • Polished Tips
  • Increases Exhaust Flow
MSRP $730.99
$652.99
You save 11%

Borla 2-1/2" Dual Exit Atak Axle-Back Exhaust System with 3-1/2" Polished Tips for 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Upgrade your 2012-2018 Jeep JK Wrangler with this premium Dual Exit Atak Axle-Back Exhaust System with 3-1/2" Polished Tips from Borla. Give your JK a loud, aggressive exhaust sound and increase horsepower with this premium kit!

Features and Benefits of the Borla 2-1/2" Dual Exit Atak Axle-Back Exhaust System with 3-1/2" Polished Tips (11860):
- Made out of T-304 stainless steel
- 2-1/2" mandrel bent piping
- Atak muffler with dual exit 2" pipes
- 3-1/2" square rolled angle cut polished tips
- Adds bold, aggressive exhaust note to your JK
- Enhances airflow
- Increases horsepower
- CNC machined for a precise fit

Borla's Atak mufflers produce the highest available decibel levels while retaining clarity of sound and avoiding distortion typically found in louder exhaust systems. This exhaust kit features a straight through baffled design and is manufactured from aircraft-quality T-304 stainless steel. Full 2-1/2" mandrel bent piping leads to the Atak muffler with dual exit 2" pipes and 3-1/2" square rolled angle cut tips that exit the rear of your JK. Ultra-smooth mandrel bends ensure maximum flow and power while precision computer-controlled CNC construction ensures an accurate fit.

Borla exhaust systems feature patented straight-through and multi-core technology to unleash hidden horsepower. Increased exhaust velocity adds power, driving excitement, fuel economy and the distinctive Borla Sound of Power respected by motoring enthusiasts everywhere.

Order Borla's 11860 2-1/2" Dual Exit Atak Axle-Back Exhaust System with 3-1/2" Polished Tips for your 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Video Transcript

If you've been following our YouTube channel, you've seen we've done a ton of LED upgrades to our 2016 Jeep Wrangler, but it still has the factory exhaust, which is just not okay. So today we're going to help it breathe better and sound better by installing this Borla Atak Axle-Back Exhaust.

This axle-back exhaust is made of 304 stainless steel tubing and features a straight-through baffle design that will help your Jeep breathe better and give it an aggressive sound. It comes with dual- polished stainless steel tips to give your Jeep a nice touch and today we're going to install it on our 2016 Jeep Wrangler.

This axle-back exhaust is going to be super easy to install. There's only one 15mm nut holding it on. Then you just have to remove the muffler from the two rubber hangers. Remove the 15mm nut on the exhaust clamp. Now we're going to remove this bracket from the rubber hanger on the Jeep. All right. Now we can move to the other hanger.

Once both hangers are disconnected, grab onto the muffler and twist it to break it loose from the pipe. Then you can pull it off. Install the provided clamp over the muffler inlet pipe. Then the hanger that came off with the factory exhaust, put that on your new muffler and then put this into place. Insert the muffler pipe into the intermediate pipe and then you can install the hangers. Install the other hanger. WD40 will help out when install these or any other kind of lubricant. Now you can tighten the clamp on the muffler. Tighten the clamp. Get it as close to the edge as you can for a better seal and now we can move on to installing the tips.

Install the provided clamp over the tip. Then install the tip onto the tailpipe. Position the tip where you want it and then tighten it with a 15mm socket. Then you can move on to the other tip. Realign your tips if you need to and your installation's finished.

All right. Let's see how it sounds. Our Borla Atak Axle-Back Exhaust is installed. It's not too loud. It gives our Jeep a nice sturdy sound. Installation will take you about 30 to 45 minutes and before you know it, you'll be heading off-road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.