Borla Axle-Back Exhaust System Stainless Steel 2-3/4" ATAK GT 2013-2014/Boss 302 2013
- Aggressive Exhaust Tone
- Stainless Steel Construction
- Polished Tips
- Increases Exhaust Flow
Borla 2-3/4" Stainless Steel ATAK Axle-Back Exhaust System for 2013-2014 GT Mustangs and 2013 Boss 302 Mustangs.
Add the fiercest axle-back available from Borla to your Mustang. This is simply the most aggressive exhaust on the market. Although this exhaust is the loudest that Borla offers, it retains clarity of sound and avoids distortion typically found in many louder exhaust systems. ATAK stands for Acoustically-Tuned Applied Kinetics and was tuned like a graphic equalizer to shape and focus sound waves for optimum high-volume output and maximum decibels. Features a straight through baffled design and manufactured from aircraft-quality 300-series stainless steel. Full 2-3/4" mandrel bent piping leads to 4-1/2" round rolled tips that exit the rear of the vehicle.
Upgrading to the Borla axle-back increases exhaust velocity to add horsepower, driving excitement fuel economy and the distinctive Borla sound. Borla axle-back exhaust systems feature patented, straight-through and multi-core technology to unleash hidden horsepower. Every system is constructed from premium austenitic stainless steel to give you the absolute best performance and durability. Ultra-smooth mandrel bends ensure maximum flow and power. Fit and finish is perfect thanks to precision computer-controlled CNC manufacturing.
Order this Borla 2-3/4" Stainless Steel ATAK Axle-Back Exhaust System for your 2013 or 2014 GT Mustang or your 2013 Boss 302 Mustang from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Intermediate skill is required for this installation.
Everything about the Borla Atak is aggressive, from the tone down to the massive four inch rolled polish tips. The whole system is stainless steel. It's a direct replacement for your factory mufflers.
We'll give you a quick before clip of the stock exhaust. Our '13 is a bone stock Automatic GT. Definitely not a bad exhaust system for a stock, but an aftermarket is definitely going to sound a lot better.
For this installation, you'll need jack and jack stands or a lift, 3/8 ratchet, 15mm socket, 13mm socket, exhaust donut removal tool, small pry bar, hammer, snips, and safety glasses.
You'll see the mufflers are located right here in the back of the car and they're held under the tail pipes by one clamp, so there's one bolt to remove. Now, we're going to work on removing it from the hanger. It's a good idea to put a towel of some sort over the tip so you don't damage your factory bumper.
Once we have it off the rear hanger, we're going to disconnect our tail pipe from our H pipe. This isn't necessary to do this. You can actually fight your way off the back, but removing this is a lot faster and it's a lot easier. Once we get that loose, we can actually just let it hang here out of the way. Now, we'll slide it forward off the front hangers. I'll spray a little lubricant into the hangers before we install our new exhaust.
The Atak requires you to reuse your original clamps. They're going to come off with your mufflers. If you look, there's a small tack actually holding them on. Using a small pry bar or a screwdriver and a hammer, you can break that right off. You'll want to put the towel back on the new muffler to protect the new tip, as well as, again, protecting the bumper. They are side specific and Borla labels it to make it easier.
Now we have the back two. We'll do the front one last. That's situated roughly where we want it and now, we can reinstall our tail pipe. First, we'll put the clamp up onto the muffler and now we'll grab our tail pipe. Now, we'll tighten up the H pipe to our tail pipes, and we'll tighten the muffler. You kind of want to center it on the rear hanger and we can hold it there while we tighten up our clamp and our installation's finished.
Let's fire it up and see how our Borla Atak sounds. The Ataks give us a nice aggressive sound from our otherwise bone stock Mustang. Our Borla exhaust not only sounds aggressive, it looks aggressive too. Installation should only take you around an hour and you'll be back on the road in no time.