Corsa Cold Air Intake APEX Series With DryTech 3D Filter EcoBoost 3.5L F-150 2017-2020/F-150 Raptor 2017-2020
Corsa APEX Series Cold Air Intake with DryTech 3D Filter for 2017, 2018, 2019, and 2020 F-150s with a 3.5L EcoBoost Engine and 2017, 2018, 2019, and 2020 F-150 Raptors.
Boost the performance of your 2017-2020 3.5L EcoBoost F-150 or 2017-2020 Raptor with this Corsa APEX Series Cold Air Intake with DryTech 3D Filter from CJ Pony Parts!
Corsa Cold Air Intake 619735-D Features and Benefits:
- Increases horsepower and torque
- Improves airflow by 30%
- Improves throttle response
- DryTech filter is System Matched to Corsa intake components for maximum gains
- Air filter is reusable and requires no oil
- Up to 50K miles between maintenance intervals depending on driving conditions
- Matte black wrinkle coat finish shield
- Plastic air duct
- No Tune required
- Includes instructions and hardware
- Made in the USA
Made in the USA, this APEX Series Cold Air Intake with DryTech 3D Filter from Corsa is designed to improve your truck's performance with a 30% increase in airflow over the stock intake system. Increases of up to 5 horsepower and 4 ft. lbs. of torque are achievable! The intake is constructed with a plastic air duct and matte black wrinkle coat finished shield. No tune is required for the installation of the intake.
The APEX Series Cold Air Intake also includes a DryTech 3D Filter. This filter is designed to specifically match with Corsa intake systems to provide your F-150 or Raptor with maximum gains. The filter does not require oil and is completely re-usable. Only needing maintenance every 50K miles depending on your driving conditions.
In the United States, one vehicle has been the nation's best seller for decades now. It can haul huge loads and tow massive trailers, yet transport passengers in complete comfort. That vehicle is the Ford F-150. While Ford has revolutionized the F-150 in recent years, aftermarket parts continue to be hugely popular as owners strive to put their own personal touches on their trucks.
Order this Corsa 619735-D APEX Series Cold Air Intake with DryTech 3D Filter for your 2017, 2018, 2019, or 2020 F-150 with a 3.5L EcoBoost Engine and 2017-2020 F-150 Raptor from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Related Categories: Ford F-150 Raptor Parts, Ford F-150 Parts, F-150 Engine, F-150 Raptor Engine, F-150 Cold Air Intakes
Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.
Installation Difficulty
Novice skill is required for this installation.
Installation Videos
Video Transcript
Tools you'll need for this installation, 7 millimeter socket, 8 millimeter socket, 10 millimeter socket, 11 millimeter socket, quarter inch ratchet, 13 millimeter socket, 3/8 ratchet, 10 millimeter wrench and a trim panel removal tool.
This Corsa intake's actually really simple to install. The first thing we're going to do is remove the factory intake. Remove the two clips on the factory air box. Remove the hose clamp on the bottom portion of the Y pipe. It's very difficult to see the head of the clamp. It's on the very back and it's a seven millimeter. Then do the upper clamp. The factory intake can now come right off. Unplug the intake sensor. The stock air filter can also be removed. Remove the 13 millimeter bolt that holds the factory air box in place. Remove the two factory clips on the air inlet. Now the whole air box can come out.
Separate the air inlet and the air box by removing this screw. We're at the workbench now. We're going to install the Corsa velocity stack onto the heat shield. Line up the bolt holes and install the provided hardware. Install the air inlet into the heat shield with the provided bolt and spacer. Insert the air inlet into the heat shield with the provided bot and spacer. Tighten it down. Install the provided weather stripping along the top of the heat shield. Install the air box assembly. Install the factory bushing between the body and the air box and use the factory bolt to secure it. Reinstall your clips into the air inlet.
Remove the sensor on the factory intake and transfer it over to your new Corsa intake. Install the provided grommet into the corset intake tube, then the sensor into the grommet. Install your couplers and clamps onto the intake tube. Install your Y plate. Tighten all your clamps. Install the massive non oiled air filter. The kit comes with this PCV tube insert. Your going to install it with this opening facing the turbo. To install it, remove the drivers side PCV hose. Remove the drivers side PCV hose by pressing the gray tab. Insert the aluminum tube with the opening facing the turbo charger or the back of the engine. Then reconnect the PCV hose.
Last thing you need to do is plug in the intake sensor. Then your installation's finished. Okay we've got our Corsa cold air intake installed on the Raptor. It was super easy to install. Practically just dropped right in. We didn't need to do any cutting or drilling and it's going to help our Raptor to breathe a whole lot better. Installation should only take you about 30 to 45 minutes and before you know it, you'll be heading Off Road.
