Corsa Cold Air Intake APEX Series With MaxFlow 5 Filter EcoBoost 3.5L F-150 2017-2020/F-150 Raptor 2017-2020
Corsa APEX Series Cold Air Intake with MaxFlow 5 Filter for 2017, 2018, 2019, and 2020 F-150s with a 3.5L EcoBoost Engine and 2017, 2018, 2019, and 2020 F-150 Raptors.
Are you looking to give your 2017-2020 3.5L EcoBoost F-150 or 2017-2020 Raptor a boost in performance? Then you should have a look at this Corsa APEX Series Cold Air Intake with MaxFlow 5 Filter from CJ Pony Parts!
Corsa Cold Air Intake 619735-O Features and Benefits:
- Increases horsepower and torque
- Improves airflow by 30%
- Improves throttle response
- Features CORSA's MaxFlow 5 high performance 5 layer, oiled cotton-gauze air filter
- Holds up to 20% more dirt than other cone-shaped filters
- Matte black wrinkle coat finish shield
- Plastic air duct
- No Tune required
- Includes instructions and hardware
- Made in the USA
Made in the USA, this APEX Series Cold Air Intake with MaxFlow 5 Filter from Corsa is designed to improve your truck's performance with a 30% increase in airflow over the stock intake system. Increases of up to 5 horsepower and 4 ft. lbs. of torque are achievable! The intake is constructed with a plastic air duct and matte black wrinkle coat finished shield. No tune is required for the installation of the intake.
The APEX Series Cold Air Intake also includes a MaxFlow 5 Filter. This filter is a high performance 5 layer, oiled cotton-gauze air filter that will provide your F-150 or Raptor with maximum gains. The design of the filter will hold up to 20% more dirt than similar cone-shaped filters. Ensuring that your 3.5L engine stays running clean!
In the United States, one vehicle has been the nation's best seller for decades now. It can haul huge loads and tow massive trailers, yet transport passengers in complete comfort. That vehicle is the Ford F-150. While Ford has revolutionized the F-150 in recent years, aftermarket parts continue to be hugely popular as owners strive to put their own personal touches on their trucks.
Order this Corsa 619735-O APEX Series Cold Air Intake with MaxFlow 5 Filter for your 2017, 2018, 2019, and 2020 F-150 with a 3.5L EcoBoost Engine or 2017, 2018, 2019, and 2020 F-150 Raptor from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Related Categories: Ford F-150 Raptor Parts, Ford F-150 Parts, F-150 Engine, F-150 Raptor Engine, F-150 Cold Air Intakes
Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.
Installation Difficulty
Novice skill is required for this installation.
Installation Videos
Video Transcript
One of the easiest ways to improve the performance of your EcoBoost is to install a cold air intake. So today we're gonna be installing this Corsa Apex cold air intake on our 2017 F-150 Raptor. This Corsa cold air intake is designed to fit your 2015 to 2018 3.5 liter EcoBoost F-150 and Raptor. It comes with a high flow intake tube and a pre-oiled max airflow filter protected by a heat shield to improve the performance and efficiency of your EcoBoost. It comes with everything you need for an easy installation so today we're going to install it on our 2017 F-150 Raptor.
Tools you'll need for this installation, seven millimeter socket, eight millimeter socket, 10 millimeter socket, 11 millimeter socket, quarter-inch ratchet, 13 millimeter socket, three-eighths ratchet, 10 millimeter wrench, and a trim panel removal tool.
Okay, this Corsa cold air intake's super easy to install. The first thing we're gonna do is remove the factory intake. Remove the clips on the air box. Loosen up your hose clamps. The second hose clamp is way back behind here. It's really hard to see, but I promise it's back there. It's a seven millimeter. Remove the intake. Disconnect your intake sensor. Remove the 13 millimeter bolt securing the air box.
Remove the clips on the front of the inlet. Then you can completely remove the air box. Separate the air box and the air inlet by removing the screw. Attach the air inlet to the Corsa heat shield. Us the provided hardware and spacer. Install the couplers and clamps onto the tube. Install the air box into the factory location. Use the factory grommet as a spacer and install the factory bolt.
Remove the driver side PCV hose 'cause we need to install a tube insert. Press on the gray tab. Lift it up. So when you go to install this tube insert, make sure the opening is facing the turbo or the back of the engine. And then reinstall the PCV hose. Install your Corsa intake tube. Tighten your clamps. Install your massive pre-oiled air filter. Install the provided weather stripping on the heat shield.
Reinstall the tube clips at the front of the air inlet. Reconnect the intake sensor. Then your installation's finished. Okay. Or Corsa cold air intake is installed. It dropped in super easy. Didn't have to do any cutting or drilling. It's definitely a really good bang for your buck to upgrade for this Raptor. Installation should only take about 30 to 45 minutes and before you know it, you'll be heading off road.
