Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970

CJ's Part Number: DS7
CJ's Low Price:
$474.99
1508198400 11815
Earn 474 RPM Points What's this?
Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970
Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970 Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970 Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970 Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970

Product Description

Aluminum 50" Driveshaft for 1965-1970 V8 Mustangs Converting to an AOD or T-5 Transmission.

Looking to shed some unwanted weight on your Pony? This 50" aluminum driveshaft is specially made to be used when installing an AOD or T-5 transmission into your early model Mustang. Balanced at 2500 RPMs. Includes correct front and rear u-joints with 1-1/16" cup diameter and 3-7/32" outside diameter/width.

Specifications:
Outside Diameter Measurement (OD): 3"
Type of Aluminum: 6061-T6 from Alcoa
Wall Thickness: .125"

*Does NOT include T-5 yoke."

Installation Instructions

Mustang Installation

Mustang Applications

This product will fit the following Mustang years:

Product Reviews

Write a review
Driveshaft Aluminum 50" AOD/T-5 Conversion V8 1965-1970 is rated 5.0 out of 5 by 1.
Rated 5 out of 5 by from USA Made 50" Aluminum Drive Shaft The 50" Aluminum AOD/T-5 Conversion Drive Shaft measures about 50" center to center of u-joint. It is shot peened for strength, nice welds and machine work, very professional looking construction, high end sealed u-joints pre-installed at factory. It appears to have been balanced as it has an aluminum balance weight welded to it on one end.
Date published: 2015-03-10
  • y_2017, m_10, d_16, h_18
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_DS7, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 9.85ms
  • REVIEWS, PRODUCT

Product Questions

Do you have a 50&1/2" center to center on u joint with rear ujoint cups 1&1/8" to fit my 8" rear  28 spline slip yoke front?  I also need bushing and seal for tail shaft t5.

Asked by: Jim 40
We only offer 50 and 51 inch driveshafts for t-5 conversions. Here is the link to the bushing, http://www.cjponyparts.com/ford-tailshaft-housing-bushing-1979-1995/p/HW2396/, here is the seal, http://www.cjponyparts.com/ford-output-shaft-seal-t-5-aod-c4/p/E2DZ7052A/ or http://www.cjponyparts.com/ford-output-shaft-seal-t-5-t-56-1994-2004/p/F4ZZ7052A/
Answered by: rk cjpp
Date published: 2017-08-31

Would this work in my 1967 Mercury Cougar? I have a 302 EFI and T5 ready to bolt it in, but I don't know if it'll fit. Thanks!

Asked by: CougarMan 67
It should work the same on a cougar.
Answered by: rk cjpp
Date published: 2017-08-22

will this fit a 66 mustang with AOD and 8" rear end?

Asked by: Mac66
Yes,This 50" aluminum driveshaft is specially made to be used when installing an AOD or T-5 transmission into your early model Mustang.
Answered by: rk cjpp
Date published: 2017-05-03

Hi, Please advise if this drive shaft is suitable for a C4 Auto in a 1969 Mustang.Also the total cost to Australia zip code 7216. Cheers Rex

Asked by: rex9977
This will not work for the c4 transmission.
Answered by: rk cjpp
Date published: 2017-05-03

Will this driveshaft work with the AOD kit on my 65 with a 9" rear axle? It's the older small bearing 9" housing

Asked by: Jcrane
The driveshaft will work, you may have to change the u-joints.
Answered by: rk cjpp
Date published: 2017-05-03

Will my original 1969 Mustang C4 Auto yoke fit this 50" DS7 Alloy shaft.

Asked by: Rex9977
It should fit, it may require a different u-joint.
Answered by: rk cjpp
Date published: 2017-05-03

What yoke do I need for aluminum driveshaft DS7 to AOD 28 spline, buying both for a AOD swap on my 70 mustang

Asked by: J1125
This yoke should fit, http://www.cjponyparts.com/ford-performance-driveshaft-slip-yoke-28-spline-c-4-aod-t-5-1965-2004/p/M4841B/
Answered by: rk cjpp
Date published: 2017-05-03

Where is this driveshaft made? USA? What brand?

Asked by: geoffh
It's unbranded, meaning it could come from a variety of manufacturers in a variety of locations.
Answered by: CJ Pony Parts
Date published: 2017-05-03
  • y_2017, m_10, d_16, h_18CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_9
  • loc_en_US, sid_DS7, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 41.83ms
  • QUESTIONS, PRODUCT

You Might Also Like