Driveshaft Slip Yoke 25-Spline V8 1965-1973

CJ's Part Number:
YK1
Driveshaft Slip Yoke 25-Spline V8 1965-1973 is rated 3.8 out of 5 by 5.
  • y_2019, m_11, d_16, h_19
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.2
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_YK1, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 154.51ms
  • REVIEWS, PRODUCT

Highlights

  • C/L To End Of Yoke: 8-1/4"
  • Width At The U-Joints: 3-1/2"
  • Width At The Yoke: 1-1/2"
  • Spline: 25 X 1-7/64"
MSRP $106.99
$99.99
You save 7%

25-Spline Driveshaft Slip Yoke for 1965-1973 V8 Mustangs.

This is a direct replacement driveshaft slip yoke for your 1965-1973 V8 Mustang. This correct 25-spline slip yoke mounts to the rear of the transmission and connects to the driveshaft.

Slip Yoke Measurements:
Centerline of U-Joint to End of Yoke: 8-1/4"
Width at the U-Joints: 3-1/2"
Width at the Yoke: 1-1/2"
Spline: 25 x 1-7/64"

Vehicle Fitment

This product will fit the following Mustang years:

Rated 1 out of 5 by from Do not fit correctly on the shaft from the gearbox This part is not available in Sweden only 28 and 31 splines Yokes
Date published: 2015-09-17
Rated 5 out of 5 by from Fits my early 25 spline T10 perfectly. I have an early '65 Fastback (Sep 1964 build) that came with a 25 spline T10 4 speed. This slip yoke fits like a glove. At some later date the factory installed T10s changed to a 28 spline tailshaft and obviously this yoke won't fit those transmissions.
Date published: 2017-09-13
Rated 4 out of 5 by from Seems fine but... The splines fit the early 4 bolt toploader just fine. However, the stock u-joint didn't fit. I had to special order a u joint Which no parts store even could fathom, let alone find a part number for. Dannysdriveshafts had one. Just an FYI.
Date published: 2015-02-11
Rated 5 out of 5 by from 1967 Cougar I swapped a 3-speed manual transmission for a Borg Warner 4-speed transmission back around 1974. After all that time the transmission needed work, the slip yoke was damaged, and the driveshaft was bent. This new slip yoke is a perfect fit and I'm back on the road again.
Date published: 2019-02-10
Rated 4 out of 5 by from 25 Spline Yoke Perfect fit, average shipping time. Cheapest price but still over priced for what you get.
Date published: 2019-02-03
  • y_2019, m_11, d_16, h_19
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.2
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_YK1, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 4.51ms
  • REVIEWS, PRODUCT

Fit a 1971 FMX?

Asked by: joe g
You would have to use the measurements found in the description to determine if it will fit.
Answered by: rk cjpp
Date published: 2019-03-06

I have a Borg Warner T10 4 speed with 25 spline output shaft, will this yoke fit my transmission?. Regards Orjan

Asked by: 59 mustang
Then which slip yoke should i use on my Borg Warner T10 with 25 spline output shaft?, it has a 289 engine. Regards Örjan.
Answered by: 59 mustang
Date published: 2018-09-13

Hi I have 73 mustang 351 Cleveland c-6 .. Can you tell which yok I can use.. . I have a drive shaft but the yok doesn't fit.. thanks Al

Asked by: flash 1
This is the only one we offer for a c-6, you would have to check how many splines your trans has, https://www.cjponyparts.com/ford-performance-driveshaft-yoke-31-spline-t-45-c-6-tremec-3550-3650-1996-2004/p/M4841A/
Answered by: rk cjpp
Date published: 2018-03-15

Will this fit a 1971 Pinto 2.0 with 4 Speed (German made engine)?  Measurements seem to indicate it would fit.

Asked by: Papa Doug
The vendor has not provided any information regarding cross-fitments of this part to any other model then what is listed.
Answered by: rk cjpp
Date published: 2018-03-15

would this be 1.09 od 25 tooth 6.5 inches on the barrel and fit a T10 transmission?

Asked by: lpiatt
This will not fit a t-10 transmission.
Answered by: rk cjpp
Date published: 2017-02-23

Assuming the pictures are correct, this yoke takes U-joint with outside snap rings. Do you offer a front U-Joint that will fit properly? Cause I can't find any

Asked by: Jack84
Please call toll free at 1-800-888-6473 and speak with a sales rep. we would need more information to try and find the correct u-joint.
Answered by: rk cjpp
Date published: 2016-11-15

Will it fit my C6 on my mach one 1973 ? IS IT SURE MY MACH ONE IS A 25 SPLINE ?

Asked by: Alain
will not fit c6
Answered by: tommyjorgensen
Date published: 2016-05-28

will this fit my 1972 351C (Q Code) with C6 trans?

Asked by: ronk2771
no..c6 use an other yoke. 
Answered by: tommyjorgensen
Date published: 2016-05-28
  • y_2019, m_11, d_16, h_4CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.2
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_en_US, sid_YK1, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 103.37ms
  • QUESTIONS, PRODUCT