Fog Light Bezel And Mounting Kit With KC HiLiTES C-Series White LED Spot And Flood Lights F-150 Raptor 2017-2020
Fog Light Bezel and Mounting Kit with KC HiLiTES C-Series White LED Spot and Flood Lights for all 2017, 2018, 2019 and 2020 F-150 Raptors.
If you're searching for a way to add some bright, new spot lights and flood lights to your 2017-2020 Raptor, look no further than this Fog Light Bezel and Mounting Kit that comes with KC C-Series White LED Spot and Flood Lights that's now available from CJ Pony Parts!
This Fog Light Bezel and Mounting Kit comes with white LED spot beam cube lights, white LED flood beam cube lights, flex LED lights with a black bezel ring and everything you'll need to install them. These lights are a great way to see more clearly in low-light conditions, like during the night time, during bad weather or if you take your Raptor off-roading! Made in the USA, this kit is the perfect solution for those who want high-quality LED spot lights and flood lights but don't want to deal with the time and hassle of trying to source every single part on their own.
This Kit Includes:
- One (1) Pair of Stainless Steel Black Powder-Coated Bezel and Mounting Brackets
- Paintable, UV-Stable Molded ABS Bezel Kit
- Stainless Steel Bracket and Light Mounting Hardware
- One (1) Pair of Silicone Protective Gaskets
- Mounting Capability for 2 Pairs of 3" Cube Lights and 1 Pair of KC HiLiTES Flex LED
- One (1) Pair of KC HiLiTES C-Series White LED Spot Beam Cube Lights
- One (1) Pair of KC HiLites C-Series White LED Flood/Spread Beam Cube Lights
- One (1) Pair of KC HiLiTES Flex LED Lights with Black Bezel Ring
Tech Tip: This kit does not include a wiring harness. We highly recommend LEDWH4 wiring harness to go along with this foglight kit. LEDWH4 harness allows for an easy connection of your 6 new lights to the factory Raptor AUX switches.
Does your Ford Raptor's lighting system match your adventurous lifestyle? If not, it would be wise to browse through CJ Pony Parts' selection of Ford Raptor LED Lighting solutions. Ford Raptor LED lights can completely transform your pickup's lighting system, while providing your truck's exterior with a little more attitude.
Order a Fog Light Bezel and Mounting Kit with KC HiLiTES C-Series White LED Spot and Flood Lights for your 2017-2020 F-150 Raptor from CJ Pony Parts today!
California Residents: Proposition 65 Warning
Installation Difficulty
Novice skill is required for this installation.
Installation Videos
Video Transcript
The F150 Raptor came from the factory with a nice set of LED headlights, but they left two big empty holes in the bumper. Today we're going to fix that, and give it a more finished look and better visibility with this LED fog light kit.
This fog light kit is designed to fit your 2017 to 18 F150 Raptor. It comes with two heavy duty brackets that bolt directly to the bumper and a mounted KC Flex, flood spotlight on each side. Black bezels are also included to give your truck a more finished look. For more information and pricing click the link in the description down below. Now let's get to the install.
Tools you'll need for this installation: quarter inch ratchet, ten millimeter socket, an extension, three eighths ratchet, thirteen millimeter socket, five millimeter hex key, thirteen millimeter wrench, seventeen millimeter wrench, and basic wiring tools.
Alright the first part of this install is assembling the bracket. We're going to take these U clips right here and put them over the bracket. You want the nut part facing towards the front of the bracket.
Next we're going to install these bezels into the bracket, these are labeled P for passenger side and D for driver's side. Make sure you grab the right one. Push up on the bottom, get it to snap in place. If these don't snap in for you, you might need to trim this edge right here. There might be some extra plastic on there from the casting process. That's looking pretty good.
Okay. The lights can now be installed. We're going to use the provided hardware with the brackets to install these KC lights. These do need to be spaced to mount properly with the bracket. Once you get the bolt through, you're going to put on a thick washer. Then a thin washer, put it onto the bracket. Then underneath you'll use a thin washer and a nut. Do the same thing for the other cube light. Then tighten them down with a thirteen millimeter socket and wrench.
Then for this KC flex light you're just going to use a thick washer to space it out. Then secure it with the hardware that comes with the KC flex light. Then tighten it down with a seventeen millimeter wrench.
Okay, we can now go over to the truck. The kit comes with this rubber seal that you put around the edge of the bumper right here to protect the bracket from scratches. Okay, our fog lights can now be installed.
To install this fog light bracket we're going to be working with two holes up here. One right here, and one right here. Now you don't have to do anything to these holes to do this kit. I do recommend drilling this one out, or drilling the hole a little bit bigger. It will make this install a lot easier. You're going to lift the fog light bracket up, and get it behind this plate. Line up the bold holes, and install your bolts.
Okay, we got that one started. We'll get the other one in. Once you get both bolts started, tighten them down with a ten millimeter socket. Okay, once you get both bolts tightened repeat the process on the other bumper, and you can move onto wiring.
There's a couple different ways you can wire up these fog lights. You could use the wiring parts that come with the lights, but we recommend this kit that we sell. It has three connectors on the end that connects to all the fog lights. You can run this right to the factory auxiliary switches here, and even has a wire for halo lights or back lights if you have them. We're going to use this harness to connect to the number one switch for our auxiliary switches.
We're going to pull the end of the wiring harness up here next to the battery, and run this right to our auxiliary wires. We're going to connect the yellow, blue, and green wires from our wiring harness to our green wire. This will be the number one switch for the Raptor switches. Then run the wiring harness along the bottom of the bumper, and simply plug in your lights. Now we can test them out.
Okay we've got our LED fog light kit installed in our Raptor. As you can see it gives it a much more finished look, and it's going to give it a lot more visibility when heading down a trail at night. Install is not that bad, it should take you two/two and a half hours. Before you know it you'll be heading off road.
