Ford Performance Rear Differential Cover 9.75" F-150 2009-2020

Ford Performance:
M-4033-F975
Rating:
100% of 100
MSRP $250.00
$227.49
You save 9%

Ford Performance Rear Differential Cover for all 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019 and 2020 F-150s with a 9.75" Rear Differential.

Are you looking to replace the Rear Differential Cover on your 2009-2020 F-150 with a 9.75” Rear Differential since you just installed a new rear lowering kit? If that is the case, check out this Ford Performance M-4033-F975 Rear Differential Cover.

The Ford Performance Rear Differential Cover is manufactured from cast iron that features a rugged powder coated finish. When you install this Rear Differential Cover it will eliminate case distortion and ring gear and bearing cap deflection while improving support. This will lengthen the life and performance of your ring and pinion gears. Additionally, this heavy-duty cover dissipates heat much faster than the factory rear differential cover. This kit includes a rear differential cover, gasket, differential cover bolts and a magnetic drain plug. Get the Ford Performance quality you’re looking for from CJ Pony Parts!

Features and Benefits:
- Cast iron construction
- Rugged powder coat finish
- Drain and fill plugs
- Improves support
- Ford Performance quality
- Ford Performance Logo
- Made In USA

Kit Includes:
- Rear Differential cover
- Gasket
- Differential cover bolts
- Magnetic drain plug

By buying your Ford Performance parts from CJ Pony Parts, you know you're getting your Mustang parts from a reliable, reputable dealer, since CJ Pony Parts is a Top 10 Ford Performance Dealer and has been for the last 10 years. When you buy your Ford Performance parts from CJ Pony Parts, you know you have a winning combination that means dependable, quality care for your pony car.

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

We’re installing this Ford Performance Rear Differential Cover.

This rear differential cover was made right here in the USA of cast iron with a rugged powder coat finish for durability and a killer look. It's going to be much stronger than the factory one and will eliminate case distortion. There's also a much needed drain plug and a standard capacity fill plug, as well as a raised fill plug for increased fluid capacity for a higher pinion angle. It's designed to perfectly fit your 9-3/4 inch rear, so today we're going to install it on our 2018 F-150.

Okay, we have the truck up in the air. The first thing we're going to do before we remove the cover is take off all of these clips that are attached to the bolts. Now that all these are out of the way, we can remove all the bolts. Place a drain pan underneath the differential to catch the fluid when it drains and remove all the bolts. This top bolt, we're actually not going to fully remove, we're just going to loosen it slightly, like that, but remove all the rest. Now we'll remove the top bolt. Then remove the cover.

The differential's drained. Now we're going to clean all the rust off the mating surface with a piece of Scotch-Brite pad. Wipe it down with some Brite-Clean, get it nice and clean and now it's ready for the new gasket and cover. Line up the gasket so you know how it's going to install. Okay. Then install the cover. Get one of the bolts started by hand, then you can install the rest. We have two installed, now we'll just install the rest of the bolts. Once you get all the bolts installed and snugged up, torque them to 14 foot pounds.

At this time we're going to tighten the drain plug and our bottom fill plug, but then remove our upper fill plug. These use a 3/8 ratchet. Then remove our upper fill plug. The reason this has two fill plugs is because this upper one is if you have a higher pinion angle. Now our truck has a 7 inch lift on it, so our rear end is lower and it's angled up so it has more pinion angle so we're going to be using the upper fill hole for when we fill it. But if you have the stock right hut, you're going to use the lower one because if you filled it with the upper on it would overfill. So if you have a lift on your truck, you're going to want to use this upper fill hole because it gives you more fluid.

Now we're going to fill the differential with fluid. We're going to be using 75W140 and we're going to fill it up until it pours out of the fill hole. That's one. Here's quart number two. Alright that's number three. It looks to be about just under five quarts. Install the fill plug, tighten it up with a 3/8 ratchet, and our install is finished.

Okay, our Ford performance rear differential cover is installed. It's matching the theme of this truck really well and it looks way better than the factory one. It's like five times heavier than the factory one as well so it's a lot stronger and it's going to help with deflection in this rear end. You know if you fill it up to this hole right here, the factory one, it's going to take just under three quarts, but if you fill it up to here like we did it's going to take just under five. It should only take about an hour to do this and before you know it you'll be heading off-road.

Vehicle Fitment

This product will fit the following F-150 years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.