GraBars Grab Handle Front Black Pair Jeep Wrangler JK 2007-2018

100% of 100


  • For Driver/Passenger Front
  • Fits 2/4-Door JK Wranglers
  • Quick And Easy Installation
  • Made In The USA

Pair of GraBars Black Front Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Give yourself a hand while getting in and out of your 2007-2018 Jeep JK Wrangler by installing this Pair of Black Front Grab Handles from GraBars. You won't need to use the steering wheel or seats to hoist yourself into your JK any longer. These 3/4" solid steel GraBars are designed specifically for your Jeep. You can even hold onto them while driving along bumpy trails!

Features and Benefits of the Pair of GraBars Black Front Grab Handles (1001):
- Fits both 2-door and 4-door JKs
- Pair completes front driver and passenger sides
- 3/4" solid steel (not tubing)
- No drilling or dismantling required
- Bolts directly into existing OEM holes
- Simple installation
- UV protected powder coat finish
- Assists in entering and exiting your Jeep
- Dual layer rubber grips
- Includes 12.9 strength black oxide steel bolts
- Extremely rigid and not flimsy like Velcro handles
- Proudly made in the USA

These grab handles will fit 2-door and 4-door Jeep Wranglers and complete the front driver and passenger sides. They are crafted in the USA from 3/4" solid steel and feature a durable powder coat finish. You won't need to do any drilling or dismantling in order to install the GraBars handles. They bolt directly into existing holes. 

These handles are renowned as one of the best modifications you can make on your JK. Add some GraBars handles to your 2007-2018 Jeep Wrangler to make entering and exiting your vehicle a breeze for both you and your passengers!

GraBars are an American made product produced by a company of Jeep enthusiasts. They are passionate about their products and take care to produce each and every grab handle to the highest degree of quality. The welds on GraBars even receive the highest certified rating a weld can get!

Order this Pair of GraBars 1001 Black Front Grab Handles for your 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

Getting in and out of a Jeep can be pretty difficult, especially if it's lifted, so today we're going to be looking at and installing a set of these GraBars front grab handles fitting your 2007-2017 Jeep Wrangler.

If you want to make it easier to get in and out of your Jeep a set of these GraBars grab handles is exactly what you need. Made of solid three quarter inch steel, with a black powder coat finish, these grab handles bolt directly into existing holes, with a dual layer rubber grip for added comfort. They're super easy to install, and come with everything you need. Today we're going to install them on our 2008 Jeep Wrangler.

Tools you'll need for this installation 13 millimeter socket, six millimeter hex key, three eighths ratchet, and a torque wrench.

Installing these grab handles is very easy and straightforward. All you have to do is remove two bolts on the inside of this A pillar, so let's get to it. Okay. All you need for this part is a 13 millimeter socket. We're going to remove a bolt here and right up here. They're kind of hard to see, but I promise they're there. It might be helpful in removing this one if you put a little piece of towel or something in your socket, just so it doesn't fall down. Otherwise you might have to take the trim off to get the bolt if it falls. Just be careful that it doesn't drop. There you go. There we go.

It's recommended that you lubricate the bolts before installing the new hardware, because Jeep has some lock tight in their nuts, so this will make it a little easier to install. We're going to start off by installing the bolt on the bottom hole right here, and then put the spacer on the bolt. Then install it into the factory nut, but don't tighten it all the way. Just get it started with a few threads so it stays in place. Then get the top spacer in place, then the bolt. Then tighten both bolts down. Torque them both to 25 foot pounds. Then repeat the process on the other side, and your installations finished.

We got both grab bars installed. They're really going to help with getting in and out of this Jeep, and they're so strong and durable they're probably going to outlast the Jeep itself. Installation is not to bad either. It should only take about 20-30 minutes, and before you know if you'll be heading off road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.