GraBars Grab Handle Front Green Pair Jeep Wrangler JK 2007-2018

GraBars:
1001G

Highlights

  • Durable Steel Construction
  • Dual Layer Rubber Grips
  • Bolt On Installation
  • Made In The USA
MSRP $102.00
$72.93
You save 29%

Pair of GraBars Green Front Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Help yourself and your passengers enter and exit your 2007-2018 Jeep Wrangler JK with this Pair of Green Front Grab Handles from GraBars. You will no longer need to use your JK's steering wheel or seats to help hoist yourself in and out of your Jeep. You can also use these handles to steady yourself while driving along bumpy off-road trails!

Features and Benefits of the Pair of GraBars Green Front Grab Handles (1001G):
- Fits both 2-door and 4-door Wranglers
- Pair completes front driver and passenger sides
- 3/4" solid steel (not tubing)
- No drilling or dismantling required
- Bolts directly into existing OEM holes
- Simple to install
- UV protected powder coat finish
- Assists in entering and exiting your Jeep
- Dual layer rubber grips
- Includes 12.9 strength black oxide steel bolts
- Extremely rigid and not flimsy like Velcro handles
- Made in the USA

This pair of grab handles completes the front driver and passenger sides of 2-door and 4-door Jeep Wranglers. They are proudly crafted in the USA from 3/4" solid steel with a durable powder coat finish. You won't need to do any drilling or dismantling to install the GraBars handles. They bolt directly into existing holes. These handles are renowned as one of the best modifications you can make to your JK Wrangler!

GraBars are an American made product produced by a company of Jeep enthusiasts. They are passionate about their products and take care to produce each and every GraBars parts to the highest degree of quality. The welds on GraBars even receive the highest certified rating a weld can get!

Order this Pair of GraBars 1001G Green Front Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

If you own a lifted Jeep, you know it can be pretty difficult to get in and out of your Jeep, so today we're going to be looking at and installing a set of these GraBars green grab handles, fitting your 2007-2017 Jeep Wrangler. These grab handles were made right here in the USA, of solid 3/4 inch steel, with a black powder coat finish, and green double layer rubber handle for comfort and durability. They're incredibly strong, and make getting in and out of your Jeep much easier, and they can even be used off road. Today we're going to install them on our 2008 Jeep Wrangler.

Tools you'll need for this installation: 13mm socket, 6mm hex key, 3/8 ratchet, and a torque wrench. Okay, we're ready to install the grab handles. We're going to be inside the Jeep for the entire installation. These handles go right here on the A-Pillar, so all we need to do is remove two bolts: a 13mm bolt here and here. Be careful when we're moving this bolt. It can easily fall down the socket and fall behind the trim. Then the top bolt. Because Jeep uses Loctite on the factory hardware, it's a good idea to lubricate these bolts before installing them. Right now, we have the longer bolt that's provided. We're going to put some WD-40 on it. Then we're going to put the bolt through the lower hole in the handle, slide the sleeve over the bolt, and install into the lower hole that you just removed.

Get it started with a few threads, but don't tighten it all the way. Place the shorter sleeve on top of the handle. Then insert the bolt. Tighten both bolts up all the way. Finally, we have to torque both bolts to 25 foot-pounds. Once you've torqued both bolts, repeat the process on the other side. Then your installation's finished. Okay, so we got both grab handles installed. They're definitely going to make it a lot easier getting in and out of this Jeep. They're super durable, too. You can shake the whole Jeep with these things, and installation's not too bad. It should only take about 15 to 20 minutes, and before you know it, you'll be heading off road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.