GraBars Grab Handle Front Orange Pair Jeep Wrangler JK 2007-2018

GraBars:
1001O

Highlights

  • Durable Steel Construction
  • Dual Layer Rubber Grips
  • Bolt On Installation
  • Made In The USA
$102.00

Pair of GraBars Orange Front Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

This Pair of Orange Front Grab Handles from GraBars will assist you and your passengers with getting in and out of your 2007-2018 Jeep JK Wrangler. You won't need to use your JK's seats or steering wheel to hoist yourself as you enter and exit your Jeep any longer! Plus, you can hold onto these handles to steady yourself while driving down bumpy off-road trails.

Features and Benefits of the Pair of GraBars Orange Front Grab Handles (1001O):
- Fits both 2-door and 4-door JKs
- Pair completes front driver and passenger sides
- 3/4" solid steel (not tubing)
- No drilling or dismantling required
- Bolts directly into existing OEM holes
- Simple to install
- UV protected powder coat finish
- Assists with entering and exiting your Jeep
- Dual layer rubber grips
- Comes with 12.9 strength black oxide steel bolts
- Extremely rigid and not flimsy like Velcro handles
- Proudly made in the USA

These grab handles complete the front driver and passenger sides of both 2-door and 4-door Jeep Wranglers. They are crafted in the USA from 3/4" solid steel with a stylish and durable powder coat finish. You won't need to do any drilling or dismantling to install the GraBars handles. They bolt directly into existing holes. These handles are renowned as one of the best modifications you can make to your JK Wrangler!

GraBars are an American made product produced by a company of Jeep enthusiasts. They are passionate about their products and take care to produce each and every GraBars part to the highest degree of quality. The welds on GraBars even receive the highest certified rating a weld can get!

Order this Pair of GraBars 1001O Orange Front Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

Getting in and out of a Jeep can be pretty difficult especially if it's lifted. So, today we're gonna be looking at and installing a set of these GraBars Front Orange Grab Handles fitting your 2007 to 2017 Jeep Wrangler. These grab handles are made right here in the USA of solid 3/4 inch steel with a black powder coat finish and a double layer orange rubber handle for a nice look and feel.

They're incredibly strong and make getting in and out of your Jeep much easier. And, they can even be used while off road. They come with everything you need for an easy installation. So today we're going to install them in our 2008 Jeep Wrangler. Tools you'll need for this installation: 13mm socket, 6mm hex key, 3/8 ratchet and a torque wrench.

Installation of these grab bars is actually really simple. All we have to do for each bar is remove two bolts on each A pillar so we're going to start off on the inside of the Jeep on the driver's side to remove the factory bolts. Okay, all we have to do is remove two 13mm bolts, one here and one here. Be careful when removing this one, it's possible for it to fall out of the socket and fall inside of the trim. Because Jeep uses Loctite on the factory hardware it's recommended to lubricate the bolts before installing them on your grab handle. This is the longer bolt that comes with the kit. We're going to install this bolt into the lower hole on the handle.

With the bolt through you're going to put the longer spacer on the bolt then install this into the lower bolt hole that you just removed. Just get it started with a couple of threads, do not fully tighten it just yet. Do the same thing to the shorter bolt. Then insert the shorter bolt and thread it in. Finally torque both bolts down to 25 foot pounds. Then repeat the process for the other side and your installation's finished.

Okay, so we got both grab bars installed. They're definitely going to make it a lot easier getting in and out of this Jeep. Installation wasn't too bad either. It should only take you about 15 to 20 minutes. Before you know it you'll be heading off road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.