GraBars Grab Handle Front/Rear Black Set 2-Door Jeep Wrangler JK 2007-2018

GraBars:
1003
Rating:
100% of 100

Highlights

  • Durable Steel Construction
  • Dual Layer Rubber Grips
  • Bolt On Installation
  • Made In The USA
$175.00

Set of GraBars Black Front and Rear Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 2-Door Jeep JK Wranglers.

Make entering and exiting your 2007-2018 2-Door Jeep JK Wrangler simple with this Set of Black Front and Rear Grab Handles from GraBars. These handles will complete your JK's front and rear driver and passenger sides. You won't need to use your Jeep's steering wheel or seats to help hoist yourself in and out of your rig anymore! You can also use these handles to steady yourself while driving down rough and rocky off-road trails!

Features and Benefits of the Set of GraBars Black Front and Rear Grab Handles (1003):
- Pair completes front and rear driver and passenger sides
- 3/4" solid steel (not tubing)
- UV protected powder coat finish
- Assists in entering and exiting your Jeep
- Dual layer rubber grips
- Includes 12.9 strength black oxide steel bolts
- Extremely rigid and not flimsy like Velcro handles
- No drilling or dismantling required
- Bolts directly into existing OEM holes
- Simple and straightforward installation
- Manufactured in the USA

This set of grab handles is proudly crafted in the USA from 3/4" solid steel with a durable powder coat finish. You won't need to do any drilling or dismantling to install the GraBars handles. They bolt directly into existing holes. These handles are widely known as one of the best modifications you can make to your JK!

*These grab handles fit 2-door JK Wranglers ONLY. They will NOT fit 4-door models.

GraBars are an American made product produced by a company of Jeep enthusiasts. They are passionate about their products and take care to produce each and every GraBars parts to the highest degree of quality. The welds on GraBars even receive the highest certified rating a weld can get!

Order this Set of GraBars 1003 Black Front and Rear Grab Handles for your 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 2-Door Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

Getting in and out of a lifted Jeep isn't the easiest thing to do, and although we don't have a lift kit on our Jeep yet, we plan on doing one. Today, we're going to make it a little easier to get in and out of by installing this GraBars front and rear black grab handle set. These grab handles were made right here in the USA of heavy duty 3/4-inch steel with a black powder coat finish for maximum durability. They're easy to install in the factory bolt hole locations and feature double layer black rubber grips so you can easily get in and out of your Jeep, or hold onto them when off-road. They come with all the hardware you'll need, so today we're going to install them in our 2008 Jeep Wrangler.

Tolls you'll need for this installation, 10-millimeter socket, 13-millimeter socket, 5 -millimeter hex key, 6-millimeter hex key, a 3-inch ratchet, and a torque wrench. Installation of these grab handles is really simple. All you need to do is remove two 13-millimeter bolts, one here, and one here. We'll remove the first 13-millimeter. Be careful when removing this one, it has a tendency to fall out of the socket and then fall behind this trim here. Just be careful not to drop it. Remove the top one. We're ready to install our grab handle. Before you install it, though, it's recommended to lubricate the hardware that comes with it because Jeep used Loctite from the factory and the bolts can be a little bit difficult to get in, so lubricate them up to make it a little easier.

We're going to take the longer bolt and put it through the lower hole in the handle, then put the longer sleeve over the bolt and install this into the lower bolt hole. Get it started with a few threads, but don't tighten it all the way. We're also going to lubricate the shorter bolt. Place the shorter sleeve on top of the handle, then insert the bolt and thread it in. With both bolts in, we're going to tighten them up all the way. Finally, torque both bolts to 25 foot-pounds. Okay, now we can repeat the process for the passenger side and then move on to the rear handles.

Okay, so we're in the rear now, they're even easier than the front. All you have to do is remove a 10-millimeter bolt here and here. Place one of the bolts through the handle, and you're going to have the grip facing the front of the Jeep. Then you're going to use a 5-millimeter hex key to tighten it up. Do the same thing to the front. Torque each bolt to 120 inch-pounds. Repeat the process for the other side, then your installation's finished. Okay, so we got all four grab handles installed. The black grips really look nice on this Jeep. They're incredibly durable too. You can move the whole Jeep with these things, they are not going anywhere. Installation's not too bad either, it should only take you about 45 minutes and before you know it, you'll be heading off-road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.