GraBars Grab Handle Front/Rear Red Set 4-Door Jeep Wrangler JK 2007-2018

GraBars:
1005R

Highlights

  • For 2007-18 4-Door JK Wrangler
  • Sold As A Front & Rear Set
  • Quick And Easy Installation
  • Made In The USA
$175.00

Set of GraBars Red Front and Rear Grab Handles for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 4-Door Jeep JK Wranglers.

This Set of Red Front and Rear Grab Handles from GraBars will make getting in and out of your 2007-2018 4-Door Jeep JK Wrangler a breeze for you and your passengers. These handles will complete your JK's front and rear driver and passenger sides. You won't need to use your Jeep's seats or steering wheel for assistance when entering or exiting your rig any longer. Plus, you can utilize the grab handles for support when you're on bumpy off-road adventures!

Features and Benefits of the Set of GraBars Red Front and Rear Grab Handles (1005R):
- Pair completes front and rear driver and passenger sides
- 3/4" solid steel (not tubing)
- UV protected powder coat finish
- Assists in entering and exiting your Jeep
- Dual layer rubber grips
- Comes with 12.9 strength black oxide steel bolts
- Extremely rigid and not flimsy like Velcro handles
- No drilling or dismantling required
- Bolts directly into existing OEM holes
- Simple installation
- Proudly crafted in the USA

This set of grab handles is manufactured in the USA from 3/4" solid steel with a durable powder coat finish. You don't have to do any drilling or dismantling to install the GraBars handles. They bolt directly into existing holes. These handles are well known one of the best modifications you can make to your JK!

*This set of grab handles fits 4-door JK Wranglers ONLY. They will NOT fit 2-door models.

GraBars are an American made product produced by a company of Jeep enthusiasts. They are passionate about their products and take care to produce each and every GraBars parts to the highest degree of quality. The welds on GraBars even receive the highest certified rating a weld can get!

Order this Set of GraBars 1005R Red Front and Rear Grab Handles for your 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 4-Door Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

If you have bigger tires, especially a lift, it can be pretty difficult getting in and out of your jeep, so today we're going to be installing these Grab Bar Red Front and Rear Grab Handles fitting your 2007 to 2017 Jeep Wrangler.

Jeeps don't have factory grab handles to help you get in and out of the Jeep, or to help you hold on to when you're off road. These grab handles install in factory bolt locations and make your off road experience that much better. They're made of super durable three quarter inch steel and double layer red rubber handles, and they come with everything you need for an easy installation. So today we're going to install them on our 2008 Jeep Wrangler.

Tools you'll need for this installation:

10 millimeter socket

13 millimeter socket

5 millimeter hex key

6 millimeter hex key

A 3/8ths ratchet

And a torque wrench

Okay, so we're inside the Jeep. These grab handles are very easy to install. The first thing you have to do is remove the two 13 millimeter bolts right here and right here, to install the front grab handle. This bolt can be a bit tricky to remove, it can fall out of your socket, so be very careful when removing it.

Okay, so we're ready to install our grab handle now. Grab the longer bolt and lubricate it up with some WD-40, and slide it though the lower hole in the handle, then install the longer sleeve onto the bolt, and thread this into the factory location.

Install the shorter spacer on top of the grab handle. Then install the smaller bolt and thread it in. Once both bolts are installed, you can tighten them down, then tighten both bolts to 25 foot pounds. Then repeat the process on the other side, then we can move on to the rear.

Okay, we're in the back of the Jeep now, and we're ready to install the rear grab handle. There's two 10 millimeter bolts on each side that we have to remove. We're now ready to install the rear grab handle. Use the provided hardware, install if through the handle, and thread it into the factory bolt holes. Install the second bolt. Now you can tighten both down. Finally, torque both bolts to 120 inch pounds. Your installation's finished.

Our front and rear grab handles are installed, they're definitely going to be make it a lot easier getting in and out of this Jeep. They look pretty good too, and they're incredibly durable. Installation's super easy, it's going to take about 45 minutes, and before you know it, you'll be heading off road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.