Mustang Ultra Clear Headlight Kit (1994-1998) Installation Instructions

1994-1998 Mustang Ultra Clear Headlight Kit

The Ultra Clear Headlight Kit will fit all 1994-1998 Mustangs.

After many years, the headlights on SN95 Mustangs are prone to turning yellow from the sun and exposure to the elements. While you can brighten them up, the only way to really combat this problem and prevent it from coming back is to replace them. This new Ultra Clear Headlight Kit really brightens up your lights, not just in how they look, but in how they perform. Order new headlights for your 1994-1998 Mustang today.

This Install Also Applies To:

• Mustang Ford V6/GT Headlight Kit 1994-1998
• Mustang Ford Headlight Assembly V6/GT 1994-1998
• Mustang Reproduction V6/GT Headlight Kit 1994-1998
• Mustang Headlight Cobra Style Smoked With Amber Reflectors Kit 1994-1998
• Mustang Headlight Kit Cobra Headlight Kit 1994-1998
• Mustang Headlight Smoked With Amber Reflectors Kit 1994-1998
• Mustang Headlight Assembly Reproduction Cobra 1994-1998
• Mustang Headlight Assembly Driver Side V6/GT 1994-1998
• Mustang Headlight Assembly Passenger Side V6/GT 1994-1998
• Mustang Headlight Assembly Replacement Pair V6/GT 1994-1998
• Mustang Marker Light Amber Ford Driver Side 1994-1998
• Mustang Marker Light Amber Ford Passenger Side 1994-1998
• Mustang Parking Light Stock Style 1994-1998

Tools Required:

• Flashlight
• Hammer
• Needle Nose Pliers
• Flat Head Screw Driver

Install Difficulty:

• 
• Easy Project

1. To begin the installation of your new Mustang Ultra Clear Headlight Kit, remove the nut that is holding the existing side marker assembly in place using a 10mm socket. Slide the side marker assembly out gently as the connector will still be attached. Unplug the connector and remove the side marker assembly completely.

2. Turn and remove the amber light bulb from the side Mustang marker light and place in a safe place as you will use this bulb in your new assembly.

3. Unplug the connector from the Mustang headlight.

4. Remove the Mustang headlight retaining clip using pliers from the top bolt closest to the outside of the vehicle.

5. There will be 2 tabs holding the headlight in place that that you will have press while you gently remove the headlight assembly. One tab is located on the bolt below the bolt from which the retainer clip was removed. The other tab is located on the other side of the headlight closer to the center of the vehicle. It is suggested you do one side at a time to avoid any damage to the existing assembly or vehicle.

6. Before installing your new headlights you can seal the seams with a clear silicone to avoid moisture from getting inside.

7. Comparing the location of the tabs or screw depth on the existing headlight with the new ones, adjust the depth of the screws on the new headlight assembly to match the old. Turn the star-like tabs on the Mustang headlight adjuster to adjust. This will reduce the amount of adjusting you have to do after installation is complete.

8. Slide in your new headlight assembly using the tracks on the vehicle as guides and ensuring the tabs slide into the correct holes.

9. Press slightly on each side of the headlight till the tabs pop through the holes and it is secure.

10. Install the new retaining clip that you received in the box on the top bolt. You can slide it in place with your fingers and tap it in using a flat head screwdriver and hammer to lock in place.

11. Reconnect the connector to the Mustang headlight.

12. Before installing your new side marker, ensure you install the amber colored Mustang bulb you removed in step 2 or a new amber light.

13. Place the side marker on the Mustang bumper and reconnect the connector.

14. Line up the side marker bolts with the correct holes and slide it in.

15. Reinstall the nut you removed in step 1 and tighten.

16. Repeat steps 1-15 for the other side.

17. Adjust your headlight to match using the hex bolts found on the headlights, which finishes the installation of your new Mustang Ultra Clear Headlight Kit.