Intake Manifold Cover/ Extension Kit Mustang GT 2005-2009

CJ's Part Number:
IMC17K
Rating:
98% of 100

Highlights

  • Includes Intake Manifold Cover
  • Comes with In-Demand Extension
  • Covers Throttle Body Area
  • Fits 2005-2009 GT Models
MSRP $162.99
$145.49
You save 11%

Intake Manifold Cover and Extension Kit for 2005, 2006, 2007, 2008 and 2009 GT Mustangs.

This CJ Pony Parts exclusive combines two very popular modifications in one money-saving kit. The Intake Manifold Cover was featured on the early prototype 2005 Mustangs and was so popular it is now an option on 2007-2009 Mustangs and a very popular upgrade for 2005-2006 owners. The extension picks up where the intake manifold cover stops and covers up the throttle body area for a cleaner look. This Intake Manifold Cover and Extension Kit is the perfect choice for any 2005-2009 GT Mustang.

Features and Benefits:
- Convenient, Money-Saving Kit
- Includes Popular Intake Manifold
- Extension Covers Throttle Body for Clean Look
- Fits 2005-2009 GT Mustangs

Tech Tip: 2005-2006 owners will also need to purchase the correct hardware for installation. Our part #HW2459.

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

In 2005, when Ford launched the new Mustang it was an immediate success. People loved the retro look and the new 4.6 liter three valve engine. While the engines made good power, they weren't exactly pleasing to look at. Ford realized this and in 2007 started offering an optional intake manifold cover similar to this one seen here.

If you have a 2005 through 2006 Mustang and didn't get this style of cover, today we're going to show you how to install this Power by Ford cover, and while we're at it, we're going to add this CPC throttle body cover as well.

For this installation you'll need a 1/4 inch ratchet, 8mm deep socket and a short extension.

Here you can see what we mean by the factory manifold. It's just kind of boring looking. Our manifold cover is going to be a nice upgrade. First step: remove the two bolts off the top of the throttle body. We're going to pull these rear clips off the studs to access the stud. You want to be extra careful on this side. This is going to be the vacuum line that goes to your fuel pressure module. You want to make sure that doesn't get unplugged.

Now we're going to install the two studs that are found in our intake manifold cover hardware kit. Now we're going to grab our new "Powered by Ford" cover, put it down here and slide it over the studs, and press it down over the rear studs.

We're going to reinstall the wiring harness and then the hose on the other side. Again here, double check to make sure the line did not come off the module or the t-fitting back here. Now we're going to loosely install the two front retaining nuts; just get them on a couple threads each. Now we can put on the throttle body cover.

The intake manifold cover is designed to be used with a stock throttle body and has this cut-out in the middle. It can be used with aftermarket throttle bodies but will require trimming. The same thing goes for the throttle body cover. It's designed for a stock throttle body and a stock air inlet but can be trimmed to fit other designs.

I'm going to slide our throttle body cover over the studs, slide it down into place and tighten it down, and our installation is finished.

Our intake manifold and throttle body cover combination made a huge improvement in our engine bay. Installation should only take you around 20 minutes. You'll be back on the road in no time. For more helpful install videos like this one, make sure you subscribe to our YouTube channel.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.