JLT Performance Oil Separator 3.0 Front Side Black Anodized Kit Focus ST 2013-2018

JLT Performance:
3021F-B
JLT Performance Oil Separator 3.0 Front Side Black Anodized Kit Focus ST 2013-2018 is rated 5.0 out of 5 by 5.
  • y_2019, m_10, d_17, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_OILSEP74, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 108.16ms
  • REVIEWS, PRODUCT

Highlights

  • Black Anodized Finish
  • Multi Stage Filter System
  • Billet Aluminum Construction
  • Holds 3Oz Of Fluid
$149.00

JLT Performance Black Anodized Front Side 3.0 Oil Separator Kit for 2013, 2014, 2015, 2016, 2017 and 2018 Focus STs.

If you're looking for an easy way to keep oil from getting into your 2013-2018 Focus ST's intake, then chances are you’re looking for an oil separator. Fortunately, CJ Pony Parts carries this JLT Performance Black Anodized Front Side 3.0 Oil Separator Kit!

Features & Benefits:
- Newly Redesigned Tank Holds 3 Oz. of Fluid
- Thick Billet Aluminum Construction with a Black Anodized Finish
- Simple Installation onto the Front Side of Engine
- Multi-Stage Filter System With Fine Mesh Stainless Steel Screen
- Knurled Tank Base for Easy Disposal of Collected Oil
- O-Ring Included to Keep the Seal Tight and Prevent Leaks
- Protects and Extends Other Engine Performance Upgrades

This JLT Performance 3021F-B Black Anodized Front Side 3.0 Oil Separator Kit is made out of thick billet aluminum with a black anodized finish. Its newly redesigned tank means the canister will hold up to 3 oz. of fluids (as compared to the previous version, which only held 1 oz.). It's easy to install and features a multi-stage filter system. This filter system has a fine mesh stainless steel screen that captures fine oil vapors. When enough of these vapors collect and become heavy enough, they'll drop to an aluminum honeycomb filter where they eventually become bigger drops. When those drops are heavy enough, they'll fall to the bottom of the canister, which will prevent them from passing on to your Focus' intake system. When you're ready to dispose of the collected oil (recommended every 5,000-7,000 miles), simply unscrew the canister and empty it.

Tech Tip: This kit is specific for the front side of the intake of a 2013-2018 Focus ST engine and should be used in combination with the rear side for optimal protection. Please see CJ Pony Parts # OILSEP72.

Order a JLT Performance 3021F-B Black Anodized Front Side 3.0 Oil Separator Kit for your 2013, 2014, 2015, 2016, 2017 or 2018 Focus ST from CJ Pony Parts today!

Note: This item is not CARB (California Air Resource Board) exempt and is not legal for sale or use in the state of California.

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Vehicle Fitment

This product will fit the following Focus years:

Rated 5 out of 5 by from Very pleased! The installation was a pain and caused me to bleed all over the intake, but I finally got in on! I took the suggestion of a previous poster and cut the old hose off the engine fitting. My car is a 2013 and the hose would not budge! Also the new hose did not have a clamp on the engine side and after I got everything buttoned up, I noticed it had slip off the fitting on the engine. I used a small tie wrap to keep it in place. I left the intake hose marked to give me a good place for future intake valve cleaning.
Date published: 2018-06-30
Rated 5 out of 5 by from It really works but pain in the A** to install It really works if you do both at the same time but OMFG getting everything moved out of the way and getting the hoses to disconnect and the one to the PCV valve only way I could get it off was to use an xacto knife and cut. once everything was back in place and I started the car it was so nice. But I did both on the same day.
Date published: 2017-09-30
Rated 5 out of 5 by from Must Have A little harder to install than it looked on the video, quite hard to get the hose off the green PCV tube. Ended up removing the inlet manifold to make it easier. My ST has only done 30k but already quite a bit of build up on some of the valves and quite a bit of oil in the manifold. IMO a worthwhile addition.
Date published: 2017-08-03
Rated 5 out of 5 by from Hopefully it helps After reading all the internet stories of coked up valves, I purchased this as a start, 44,000 miles on the car, valves looked terrible...hoping it helps some.
Date published: 2019-02-19
Rated 5 out of 5 by from Well made parts. The product made well and installed easily. Glad i chose this one for my focus st
Date published: 2018-05-30
  • y_2019, m_10, d_17, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_OILSEP74, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 4.09ms
  • REVIEWS, PRODUCT

Will this fit 2015 focus SE?

Asked by: Jacob
Sorry it will not fit an focus se.
Answered by: rk cjpp
Date published: 2019-01-03

clearly said 'will fit 2013-2018' What should I get for my 2018 ST?

Asked by: BRANDEN
This fits the 2018 st.
Answered by: rk cjpp
Date published: 2018-12-12

Why won't this work with a 15 to 18 st? Are they not the same setup?

Asked by: Cburckhardt
No they are not.
Answered by: rk cjpp
Date published: 2018-12-11
  • y_2019, m_10, d_17, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_3
  • loc_en_US, sid_OILSEP74, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_cjponyparts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 139.75ms
  • QUESTIONS, PRODUCT