K&N Cold Air Intake Kit FIPK 5.3L/6.2L Chevrolet Silverado 1500/GMC Sierra 1500 2014-2015

K&N:
57-3082
Rating:
100% of 100

Highlights

  • Increases Horsepower
  • Improves Throttle Response
  • Air Filter Is Washable
  • 50 State Emissions Legal
MSRP $473.19
$260.99
You save 45%

K&N FIPK Cold Air Intake Kit for 2014 and 2015 Chevrolet Silverado 1500s and GMC Sierra 1500s with a 5.3L or 6.2L Engine.

If you want to give your 2014-2015 Chevrolet Silverado or GMC Sierra a big performance boost, then you're going to need to upgrade to an air intake that'll move more cold air to your engine to increase its horsepower. Fortunately, K&N makes this high-quality Cold Air Intake Kit and it's now available at CJ Pony Parts!

Features & Benefits:
- Smooths and Straightens Air Flow to Your Engine for Better Air Intake
- Increases Horsepower
- Improves Throttle Response and Engine Sound
- Replaces Your Entire Factory Air Intake System
- Can Last Up to 100,000 Miles Before Service is Required
- Includes a Free-Flowing High-Density Polyethylene Tube
- Tube Accommodates Factory Mass Air Sensor and Crank Case Vent Hoses
- Chrome-Topped High-Flow Air Filter is Washable and Reusable
- Heat Shield Installs in the Original Air Box Space
- Simple Installation: Takes About 90 Minutes and Uses Factory Mounting Points

This K&N 57-3082 FIPK Cold Air Intake Kit smooths and straightens the air that flows into your engine to give it better air intake. More air means more usable power and more usable acceleration throughout your 5.3L or 6.2L engine's RPM range! You'll see an increase in horsepower and an improvement in throttle response, not to mention an improvement in what your engine sounds like! This Cold Air Intake Kit will replace your entire factory air intake system, and it can last up to 100,000 miles before being serviced (depending on driving conditions and how you drive). The kit comes with a free-flowing high-density polyethylene tube that will accommodate your factory mass air sensor and crank case vent hoses and a heat shield that you'll install in the original air box space. Plus, the included chrome-topped high-flow air filter is washable and reusable, which will save you some money in the long run! And installation is quite simple: it'll only take about 90 minutes or so and you'll use your factory mounting points.

K&N FIPK Cold Air Intake Kit Specifications:
Air Filter Color: Red
Air Filter Material: Cotton Gauze
Air Filter Outlet Shape: Round
CARB EO Number: D-269-49
Clamp Material: Stainless Steel
Clamp Style: Regular
Clamps Included: 5
Couplers Included: 1
Intake Pipe Color and Finish: Black
Intake Pipe Material: High-Density Polyethylene
Street Legal in All U.S. States: Yes
TUV Approved (Europe): No
Type: Gen II

Order a K&N 57-3082 FIPK Cold Air Intake Kit for your 2014 or 2015 Chevrolet Silverado 1500 or GMC Sierra 1500 with a 5.3L or 6.2L Engine from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Difficulty

Easy
Easy

Novice skill is required for this installation.

Installation Videos

Video Transcript

Today on CJ Off Road we're going to ditch the factory intake our 6.2 liter 2017 Silverado to make it breathe and sound a whole lot better. K&N is one of the biggest names in aftermarket cold air intakes and our 2017 Silverado with a 6.2 liter engine is still breathing through a straw with the factory intake. So today we're going to install this K&N cold air intake. This cold air intake is designed to be a direct fit replacement for the factory one on your Silverado with a 5.3 or 6.2 liter engine. It features a high flow polyethylene intake tube, a large pre-oiled air filter protected by a heat shield and all the hardware and couplers that you'll need for installation. It's going to help your truck to breathe better and it's legal in all 50 states and the best part is, it's super easy to install.

Tools you'll need for this installation: 8mm socket, 10mm socket, an extension, T-15 Torx bit, 1/4" ratchet, 3mm hex key, 4mm hex key and an adjustable wrench.

All right, this K&N cold air intake is actually really easy to install. The first thing that we're going to do is remove the big, ugly and restrictive factory intake. The first thing we're going to do is disconnect both PCV hoses from the air intake. Press on the gray tab and pull it right off. It's kind of hard to see, but next we're going to loosen the clamp on the throttle body. There's a screw on each corner of the air box that needs to be removed. The intake can now be removed. Remove the air filter. Remove the bottom portion of the air box just by pulling it up and out of its grommets. Remove the four bolts that secure the air box mounting tray. Remove the tray. Grab your K&N heat shield and install the provided weather stripping around the trim.

You can cut off the excess. To give us a little bit more room, we're going to remove this 10mm bolt right here. Then move the support bar out of the way. Install your heat shield into the truck. Now once you get it in place, secure it with three of the factory screws. Install the filter adapter onto the air filter. Tighten down the clamp. Secure the air filter with two of the provided bolts. We're going to install this support bar. Remove both PCV hoses from the engine. Install a coupler and clamp onto the filter adapter and then tighten the clamp. Using a T-15 Torx bit to remove the factory mass air flow sensor. Install the gasket onto the intake tube for the mass air flow sensor then place the adapter onto the intake tube and secure it with the provided hardware.

Then secure the mass air flow sensor to the adapter. Install the provided hose parts into the intake tube. You don't need to over-crank these, just get them snug. For the throttle body side of the intake tube, there is two different coupler options. This one is for the 5.3 liter engine and this one is for the 6.2. Put the 6.2 coupler on there and now it's ready to go on the truck. Then tighten down your clamps. Plug in your mass air flow sensor. Then use the provided hose for the PCV ports. Okay, we've got our K&N cold air intake installed on our Silverado. We've got rid of that ugly factory intake. It looks a whole lot better under the hood. And it should definitely help this truck to breathe a whole lot better too. Installation shouldn't take you more than an hour and before you know it you'll be heading off road.

Vehicle Fitment

This product will fit the following Sierra years:

  • 2014,
  • 2015,

This product will fit the following Silverado years:

  • 2014,
  • 2015,
Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.