Kentrol Hood Catch Black Pair Jeep Wrangler JK 2007-2018

Kentrol:
50571

Highlights

  • Stainless Steel
  • Black Powder Coat Finish
  • Direct-Fit Replacement
  • Includes Necessary Hardware
MSRP $114.44
$108.99
You save $5.45

Pair of Kentrol Black Hood Catches for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Are you looking for a way to add subtle, custom styling to your Wrangler? Try this Pair of Black Hood Catches from Kentrol! The catches are high-quality additions for your 2007-2018 Jeep JK Wrangler’s hood made to last and look great.

Hood Catches 50571 Features:
- Made using T-304 stainless steel
- High gloss black powder coated finish
- Includes hardware necessary for installation
- Inspected for fit, finish and function
- Pair completes driver and passenger side
- Direct-fit replacements for factory catches
- Fits all 2007-2018 Jeep JK Wranglers

These black powder coated hood catches are manufactured, like all Kentrol products, using premium-quality stainless steel. Not only do they look great, but they are also reliably durable to stand up to whatever rough terrain you choose to explore. One pair completes the driver and passenger side replacement. Kentrol makes parts to last and provide maximum service life.

These catches are direct-fit replacements for your original catches and are easy to install. This pair (P/N: 50571) includes all the necessary hardware for installing them onto your JK Wrangler. Every catch is inspected before distribution for fit, finish and function to ensure you get the best quality every time.

Order this Pair of Kentrol Black Hood Catches for your 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Videos

Video Transcript

We're going to show you how to dress up the hood of your JK Wrangler.

If you're looking to eliminate hood flutter in your JK as well as dress up the hood a little bit, today we're going to be installing these control stainless steel black hood catches on to our 2008 Jeep Wrangler. These hood catches are constructed using a T304 stainless steel then finished in a durable high gloss powdered coat that features all the necessary hardware to get them installed and it fits all 2007 to 2018 Jeep JK Wranglers. With that being said, let's get them installed. Tools you need for this installation, 3/8" ratchet, 10 mm socket, and a 13 mm socket.

On our 2008 Jeep Wrangler we were experiencing a little bit of hood flutter on here. The first step of this installation is going to be to remove these factory worn out hinges, we're going to pop the hood and get started. As you can see, on the lower part of the hood latch there is a small nut on the inside. It's pretty hard to see, however you can get it with a few wobble extensions. Go ahead and remove the two 10 mm nuts up top here, and you don't need to hang on to any of this hardware. The control kit comes with everything you need. With both of those removed, you're now ready to install your new latches.

We're going to install the lower section first, as you can see there are two pins, those are going to go in the top and the stud will slide in, now you do have to put the washer and locknut on the backside which is kind of tricky to do, try not to drop the nut, if you do, hopefully it falls onto the ground. Once you get them both on, then we can go ahead and tighten this up. We're just going to use the same 13 mm socket that you used to remove the factory bolt. This little rubber isolator goes on after this is tightened. As you can see, ours was missing it, so we have a ton of paint scratch there, this is going to prevent any of that issue and it slides right over. Now we can move on to the top.

The next step is going to be to put the upper part of this bracket on. As you can see, we've got the rubber isolator as well as it's angled down in this position, we're going to slide through from the outside in. Then we're going to put washers and locknuts on both of the studs. Then go ahead and tighten both of these down with a 10 mm socket. After you have both of them tightened down, complete this same process on the other side and your installation is complete.

We just wrapped up the installation of this control black stainless steel hood catches onto our 2008 Jeep Wrangler. These look really nice, plus they're going to eliminate any possibility for hood flutter in the future. It was a super simple installation, only took about 30 minutes to get done. You can find them here as well as many other great parts for your JK, at CJPonyParts.com.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.