MagnaFlow Loop Delete Pipe Assembly Jeep Wrangler JK 2012-2018

MagnaFlow:
15313

Highlights

  • Stainless Steel
  • High Flow Design
  • Aggressive Exhaust Tone
  • Bolt On Installation
MSRP $182.08
$120.00
You save 34%

MagnaFlow Loop Delete Pipe Assembly for 2012, 2013, 2014, 2015, 2016, 2017 and 2018 Jeep JK Wranglers.

Eliminate the stock loop section after the catalytic converter on the driver side of your 2012-2018 Jeep Wrangler JK with this Loop Delete Pipe Assembly from MagnaFlow This pipe is designed and engineered to work with long arm travel lift kits which interfere with the factory loop.

Features and Benefits of the MagnaFlow Loop Delete Pipe Assembly (15313):
- Stainless steel construction
- Eliminates stock loop section after catalytic converter
- Mandrel-bent tubing
- Includes required hardware
- Engineered to work with long arm travel lift kits
- Fits ALL 2012-2018 2-Door and 4-Door JK Wranglers

MagnaFlow manufactures this Pipe from premium-grade stainless steel for long lasting durability. It features mandrel-bent tubing for endurance and superior air flow. The hardware you will need for installation is included.

Tech Tip: You can also eliminate the factory loop section with MagnaFlow's direct replacement Y-Pipe (CJ's Part # 19211).

*You will need to cut your Jeep's factory Y-Pipe for installation of these Loop Delete Pipe.

CJ Pony Parts offers a wide variety of MagnaFlow products for our customers. If you're looking for one of the top performing and best sounding exhausts on the market, you'll want to check out our selection of MagnaFlow parts.

Order MagnaFlow's 15313 Loop Delete Pipe Assembly for your 2012, 2013, 2014, 2015, 2016, 2017 or 2018 Jeep JK Wrangler from CJ Pony Parts today!

California Residents: Proposition 65 Warning

Installation Difficulty

Moderate
Moderate

Intermediate skill is required for this installation.

Installation Videos

Video Transcript

Every Jeep owner loves going off-roading. When lifting your Jeep and taking it off road, you can run into clearance issues with the factory loop pipe. One way to combat that issue is by deleting the loop pipe entirely. Today, we're going to give our Jeep some better clearance by installing this MagnaFlow loop delete pipe.

This MagnaFlow loop delete pipe is made of two and a half inch mandrel bent stainless steel tubing. It's designed to accept long arm travel kits while retaining the factory catalytic converters. It's going to help when we lift our Jeep and take it off road for better clearance so today we're going to install it on our 2016 Jeep Wrangler. Tools you'll need for this installation: a lift or a jack and jack stands, 3/8" ratchet, 13 mm socket, 15 mm socket, 16 mm wrench, 17 mm wrench, a marker, tape measure, safety glasses, and a Sawzall or hacksaw.

We got the Jeep up in the air. The very first thing we're going to do is mark the loop pipe where it needs to be cut. We're not going to disconnect it from anything yet. All we're going to do is make the cut and then we'll disconnect it. Here is the loop pipe. As you can see, it's big and it can get in the way. How we're going to get rid of this, we're going to cut it out, make a mark, cut it out, and then put in our new section.

Grab yourself a tape measure and you're going to measure from the weld on the catalytic converter three inches back. Make a mark at three inches behind the weld on the catalytic converter and that's where you're going to make your cut. That's where we have to make our cut. Before we remove any of the bolts, especially right here on the y-pipe, we're going to spray with some penetrating lubricant. They were pretty corroded and we want to make it a little bit easier on ourselves.

Give those a couple minutes to soak in and then you can try to break them free. After you let them soak with penetrating lubricant, we can break them loose. Remove the second bolt on that loop pipe, then remove the loop pipe itself. With the loop pipe gone, we're going to unbolt the passenger side of the y-pipe just to give us a little bit more wiggle room to get the loop delete pipe in.

You don't need to remove the y-pipe, just unbolt it up here and it'll give you a lot of wiggle room. Grab your MagnaFlow loop delete pipe, place the provided flange over it, and also the clamps, then install this end onto the catalytic converter and this end onto the y-pipe side. With the loop delete pipe in place you can now install the hardware. Get these bolts nice and tight then you can move up to tightening the clamp. Tighten the clamp with a 15 mm socket. With the loop delete pipe in place, you can reinstall the y-pipe on the passenger side, then your installation's finished.

Our MagnaFlow loop delete pipe is installed. Installation really isn't that bad. It should only take about an hour to an hour and a half. Make sure you measure twice and cut once and before you know it you'll be heading off road.

Vehicle Fitment

This product will fit the following Wrangler years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.