Mishimoto Intercooler Pipe Kit Polished Aluminum Mustang EcoBoost 2015-2021

100% of 100


  • Replaces Hot/Cold-Side Pipes
  • Mandrel-Bent Aluminum
  • CNC-Machined BPV Flange
  • Highly Polished Finish
MSRP $514.64
You save 22%

Mishimoto Polished Aluminum Intercooler Pipe Kit for 2015, 2016, 2017, 2018, 2019, 2020, and 2021 EcoBoost Mustangs.

Are you looking for a way to improve spool-up, increase power potential, and improve engine bay aesthetics on your EcoBoost Mustang? If so, Mishimoto has you covered with their new intercooler pipe kit designed specifically for your 2015-2021 EcoBoost Mustang.

Features and Benefits:
- Direct-fit for the 2015-2018 EcoBoost Mustang
- Replaces Hot-Side and Cold-Side Intercooler Pipes
- Mandrel-Bent Aluminum Pipes Eliminate Restrictive Bends
- CNC-Machined BPV Flange on Hot-Side Pipe
- Cold-Side Pipe Allows for Quick Install of Meth Injection or a Boost Gauge
- Fits OEM, Mishimoto and Other Factory-Style Intercoolers
- Beautiful Highly Polished Finish on ALL Piping
- Easy Installation Takes Less Than 1 Hour

This kit features 2-1/2" hot-side and 2-3/4” cold-side mandrel-bent aluminum piping for smooth airflow, and four-layer silicone couplers with heat-resistant embedded fibers for improved tolerance against heat and pressure. Also included is high-quality stainless steel T-bolt clamps. Installation is simple and does NOT require any modifications to any parts in the engine bay, and can be completed in under one hour.

This Kit Includes:
- (1) Cold-Side Intercooler Pipe with NPT Bung
- (1) Hot-Side Intercooler Pipe with BPV Flange
- (4) Silicone Couplers
- (1) 2.0" T-Bolt Clamp
- (4) 2.75" T-Bolt Clamps
- (3) 3.0" T-Bolt Clamps

Installation Torque Specs: 27 in-lbs is recommended for all t-bolt and constant tension t-bolt clamps. These clamps have an operating range of 18-35 in-lbs. Do NOT exceed the maximum torque rating of 35 in-lbs.

California Residents: Proposition 65 Warning

This item is 50-state legal (CARB E.O. Number D-759)

Installation Videos

Video Transcript

The intercooler is going to be an integral part of any turbo charger system. Since a turbo runs off exhaust, it creates a lot of heat and that heat has to be cooled down in the piping before it goes in the intake to make any kind of power. Now in our EcoBoost Mustang, the factory inter-cooler is okay for stock boost levels, but as soon as you turn it up it becomes very inefficient. This car here already has an aftermarket inter-cooler, but still has the factory inter-cooler pipes which can also be a restriction. Today we're going to upgrade them using this inter-cooler pipe kit from Mishimoto.

This inter-cooler pipe kit from Mishimoto is 50 state legal and it will work on any 2015 through 2017 EcoBoost with either a stock inter-cooler or an aftermarket inter-cooler that uses the stock pipes. Features smoothly bent pipes with a polished finished, plus all necessary couplers and clamps for installation.

For this installation I need a lift or jack and jack stands, quarter inch ratchet, 7mm socket, 10mm socket, short extension, 5mm Allen key and a panel removal tool.

Freddy here is our resident turbo guy. He's going to give me a hand with the installation. The first thing we're going to do is remove the splash pan by removing the screws on the edges, the screws on the back and the plastic push pins.

Now what we're going to do now, you can see the inter-cooler, so we disconnect the pipes down here. Then we're going to move up to the engine bay and disconnect up there next.

Now we're up in the engine bay. We're actually going to disconnect the pipe here from the turbo.

We have to pull up this harness here from the pipe.

Then, as you're fishing out, don't forget unplug blow off valve.

With the hot side off, now Freddy's going to remove the pipe that goes to our throttle body.

To prepare the installation of our Mishimoto pipes what we're going to do now is take the blow off valve and move it over to the new pipe. Also an excellent time if you're looking to upgrade your blow off valve, which I do suggest. This would be a good time to do it.

Now we're going to start assembling the pipe with the provided couplers.

We're going to do the same thing at the bottom of the pipe.

Now Freddy's going to assemble our cold side pipe. When assembling this side of the pipe, the coupler with the larger diameter and the longer end is going to go on the pipe itself. The other end's going to go to the cooler. Remember, the clamps just have to be snug for now. We're going to adjust everything on the car.

Now we're ready to install the piping. We're going to feed it down to the inter-cooler. Don't forget to plug in your blow off valve.

When we have everything in place, then we'll come back and tighten it.

We're going to pull the hose down and get it over the inter-cooler. Sometimes we use different parts and mix and match if we do run into some issues. In our case the clamp provided by Mishimoto was a little small. We're going to reuse the one that was on the car.

Now, Freddy did the same thing on the cold side to connect the tube to the cooler and the throttle body.

Again, same issue on this side, because of the aftermarket inter- cooler we do need a larger clamp to put the coupling over the inter-cooler.

Now we're going to go back through and tighten all the clamps. Make sure everything's adjusted properly.

Freddy's going to do the same thing now over on the cold side. Just make sure all the pipes are lined up properly, sit in the couplings where they need to be and then tighten them down.

With everything tight up top now we're going to move down below and tighten up the last clamp. Make sure everything's lined up, everything's tight. Reinstall the splash pan and installation's finished.

Overall the Mishimoto pipes fit nicely on our EcoBoost and do a much better job of getting air flow to and from our inter-cooler. Again, if you're running higher horsepower with the boost turned up, this is something you definitely want to consider. It's also available in the polished finish shown here, along with a black finish. Take you probably around two hours to install. You'll be back on the road in no time.

Vehicle Fitment

This product will fit the following Mustang years:

Only registered users can ask/answer questions. Please sign in or create an account.
Write Your Own Review
Only registered users can write reviews. Please sign in or create an account.